TAMU Turbo Show 1972 Turbomachinery Analysis and Protection John S. Sohre 1 Diagnostics
TAMU Turbo Show 1972 Centrifugal Compressor Operation and Maintenance Hugh M. Davis 10 Centrifugal Compressors
TAMU Turbo Show 1972 Commissioning a Gas Turbine Compressor or Single Lift Package for Offshore Gas Reinjection Application Ramana Reddy 26 Centrifugal Compressors; Gas Turbines
TAMU Turbo Show 1972 Fluid Film Bearing Design Considerations Stanley Abramovitz 39 Bearings
TAMU Turbo Show 1972 High Speed Journal and Thrust Bearing Design Bernard S. Herbage 56 Bearings
TAMU Turbo Show 1972 Selection and Application of High Speed Gear Drives John M. Phinney 62 Gears
TAMU Turbo Show 1972 Fundamentals of Lubrication Relating to Operation and Maintenance of Turbomachinery Allen M. Clapp 67 Lubrication Systems
TAMU Turbo Show 1972 Turbomachinery Specifications John G. Housman 75 Specifications
TAMU Turbo Show 1972 New Developments in Compressor Aerodynamics Meherwan P. Boyce 79 Centrifugal Compressors
TAMU Turbo Show 1972 Aerodynamics of Turbines William E. Thompson 90 Turbo Expanders
TAMU Turbo Show 1972 New Technology in Turbine Aerodynamics Arthur J. Glassman, Thomas P. Moffitt 105 Gas Turbines
TAMU Turbo Show 1972 Rotor-Bearing Stability Edgar J. Gunter, Jr. 119 Bearings; Rotordynamics
TAMU Turbo Show 1972 Rotor Design and Vibration Response Firm L. Weaver 142 Rotordynamics
TAMU Turbo Show 1972 Present Instrumentation and Future Trends in Real Time Analysis Equipment Ira M. Langenthal, Frank Kasper, Jr. 148 Condition Monitoring
TAMU Turbo Show 1972 Application of Spectrum Analysis to Onstream Condition Monitoring and Malfunction Diagnosis of Process Machinery Jan S. Borhaug, John S. Mitchell 150 Condition Monitoring
TAMU Turbo Show 1972 Oil Systems—Design for Reliability Michael D Innocenzio 163 Lubrication Systems
TAMU Turbo Show 1972 Turbomachinery Operation and Maintenance Charles J. B. Mitchell 168 Condition Monitoring
TAMU Turbo Show 1973 Cold and Hot Alignment Techniques of Turbomachinery Charles Jackson 1 Alignment
TAMU Turbo Show 1973 Optical Alignment of Turbomachinery A. J. Campbell 8 Alignment
TAMU Turbo Show 1973 Industrial Applications of Aircraft-Derivative Gas Turbines Robert Harnsberger 13 Gas Turbines
TAMU Turbo Show 1973 Conversion of a Single-Shaft Turboprop Engine to a Two-Shaft Industrial Turbine John D. Horth 20 Gas Turbines
TAMU Turbo Show 1973 Critical Areas in Centrifugal Compressors Paul Lewis 29 Centrifugal Compressors
TAMU Turbo Show 1973 Case Histories of Specialized Turbomachinery Problems J. C. Wachel, Walter VonNimitz, Fred R. Szenasi 33 Condition Monitoring
TAMU Turbo Show 1973 Repair Techniques for Rotor and Case Damage Harry E. Erb 51 Maintenance
TAMU Turbo Show 1973 Maintenance Techniques for Turbomachinery William E. Nelson 65 Maintenance
TAMU Turbo Show 1973 Developments in Multiple Fuel Applications for Gas Turbines James G. Kiernan 70 Gas Turbines
TAMU Turbo Show 1973 Corrosion Problems in Turbines Mauricio Casanova 83 Corrosion; Gas Turbines
TAMU Turbo Show 1973 On-Stream Cleaning of Turbomachinery Brian Turner 91 Operation
TAMU Turbo Show 1973 Application of Screw Compressors for Processes in the Chemical and Petrochemical Industries, The Helmut Kammerer 94 Screw Compressors
TAMU Turbo Show 1973 New Coupling Applications or Application of New Coupling Designs Ken Kraemer 103 Couplings
TAMU Turbo Show 1973 Some Metallurgical Considerations in Centrifugal Compressors Joseph A. Cameron, Frank M. Danowski, Jr. 116 Centrifugal Compressors; Materials
TAMU Turbo Show 1973 Real Time Spectral Analysis—Taking the Mystique Out of This Valuable Maintenance Tool Jon E. Palm 129 Condition Monitoring
TAMU Turbo Show 1973 Compressor Performance, Field Data Acquisition and Evaluation Hugh M. Davis 143 Centrifugal Compressors
TAMU Turbo Show 1974 Power Recovery Systems and Hot Gas Expanders John P. Balfoort 1 Turboexpanders
TAMU Turbo Show 1974 Large Power-Output Radial Inflow Turbine, The Hans D. Linhardt 8 Turboexpanders
TAMU Turbo Show 1974 What is Optical Alignment? John W. Mitchell 17 Alignment
TAMU Turbo Show 1974 Field Measurements of Blade Stresses on Industrial Turbomachines R. A. Strub 23 Axial Compressor
TAMU Turbo Show 1974 Gas Turbines—High Efficiency Combined with Ease of Maintenance George T. Barker 35 Gas Turbines
TAMU Turbo Show 1974 Borescope Techniques Applied to Maintenance Practices on Marine Heavy-Duty Gas Turbines Samoil Moise 46 Borescopes; I nspection; Gas Turbines
TAMU Turbo Show 1974 Installation and Application of Sensors for Turbomachinery Monitoring, The George P. Schanzenbach 55 Condition Monitoring
TAMU Turbo Show 1974 Industrial Gas Turbine Performance Measurement J. T. Purvis 59 Gas Turbines
TAMU Turbo Show 1974 Special Purpose Gearing—A User s Approach to Sound Application Engineering J. Hans Arndt 67 Gears
TAMU Turbo Show 1974 Electric Motors for Centrifugal Compressor Drives Jesse C. Moore 74 Electric Motors
TAMU Turbo Show 1974 Field Performance Testing of Centrifugal Compressors Roy B. Pais, Gerald J. Jacobik 84 Centrifugal Compressors
TAMU Turbo Show 1974 Optimization of Various Gas Turbine Cycles Meherwan P. Boyce, Mow-Shung Chen 91 Gas Turbines
TAMU Turbo Show 1975 Impact of Recent Tilting Pad Thrust Bearing Tests on Steam Turbine Design and Performance Truman L. King, Jr., John W. Capitao 1 Bearings
TAMU Turbo Show 1975 Steam Turbine Blade Failures, Causes and Correction John S. Sohre 9 Steam Turbines
TAMU Turbo Show 1975 Analysis of Three Impeller Failures: Experimental Techniques Used to Establish Causes Charles Bultzo 31 Centrifugal Compressors
TAMU Turbo Show 1975 Examination of Pump Cavitation, Gear Mesh and Blade Performance Using External Vibration Characteristics John S. Mitchell 39 Condition Monitoring
TAMU Turbo Show 1975 Low Frequency Vibration at Centrifugal Plants Walter W. VonNimitz 47 Condition Monitoring
TAMU Turbo Show 1975 Plain Bearing Damage J. M. Conway-Jones, Anthony J. Leopard 55 Bearings
TAMU Turbo Show 1975 Rotor-Bearing System Design Audit Stanley B. Malanoski 65 Bearings; Rotordynamics
TAMU Turbo Show 1975 Design and Development of a New 30,000 HP Class Two Shaft Type Gas Turbine Arthur W. J. Upton 71 Gas Turbines
TAMU Turbo Show 1975 Gas Turbine Operation in Extreme Cold Climate R. E. Patton 83 Gas Turbines
TAMU Turbo Show 1975 Borescope Color Photography: A New Engineering Technology for Marine Gas Turbine Condition Monitoring William J. Ridler 95 Borescopes; Inspection; Gas Turbines
TAMU Turbo Show 1975 Forward Subrotative Speed Resonance Action of Rotating Machinery Donald E. Bently 103 Condition Monitoring; Rotordynamics
TAMU Turbo Show 1975 Operation History of Fractional Frequency Whirl, An Kenneth J. Smith 115 Condition Monitoring; Rotordynamics
TAMU Turbo Show 1975 Design and Application of Squeeze Film Dampers for Turbomachinery Stabilization Edgar J. Gunter, Jr., L. E. Barrett, P. E. Allaire 127 Bearings; Rotordynamics
TAMU Turbo Show 1975 High Speed Coupling Failure Analysis K. W. Wattner 143 Couplings
TAMU Turbo Show 1975 Less Costly Turboequipment Uprates Through Optimized Coupling Selection Heinz P. Bloch 149 Couplings
TAMU Turbo Show 1975 Fossil Energy: Advanced Power Systems Winfred M. Crim, Jr. 153 Energy
TAMU Turbo Show 1976 Large High Pressure Centrifugal Compressors for Oxygen Service Kenneth W. Geiser 1 Centrifugal Compressors
TAMU Turbo Show 1976 Distortion of Speed Changer Housings and Resulting Gear Failures Fred L. VanLaningham 7 Gears
TAMU Turbo Show 1976 Installation of Large Rotating Equipment Systems—A Contractor s Comments John R. Massey 15 Centrifugal Compressors; Gas Turbines
TAMU Turbo Show 1976 Site Balancing of a Large Flexible Rotor Containing Unbalance Eccentricity and Permanent Residual Bow A. Stewart Maxwell, Alan F. P. Sanderson 23 Balancing
TAMU Turbo Show 1976 Advanced Research Programs in Turbomachinery Meherwan P. Boyce, William L. Trevillion, Michael L. Brown 31 Centrifugal Compressors; Gas Turbines
TAMU Turbo Show 1976 Problems Encountered in Boiler Feed Pump Operation Elemer Makay 45 Pumps
TAMU Turbo Show 1976 Pulsations in Liquid Pumps and Piping Systems Cecil R. Sparks, J. C. Wachel 55 Piping; Pumps
TAMU Turbo Show 1976 Turbomachinery Noise Rating George M. Diehl 63 Noise
TAMU Turbo Show 1976 Reliable Overspeed Protection for Industrial Drive Turbines Firm L. Weaver 71 Steam Turbines
TAMU Turbo Show 1976 Industrial Steam Turbines Improve Energy Utilization in Thermal Power Plants R. Wickl 79 Steam Turbines
TAMU Turbo Show 1976 Efficiency in Mechanical Drive Steam Turbines John A. Brown 87 Steam Turbines
TAMU Turbo Show 1976 Practical Design Solutions for Mechanical Drive Steam Turbines Alfred M. Spechtenhauser 99 Steam Turbines
TAMU Turbo Show 1976 Coupling Misalignment Forces C. B. Gibbons 111 Couplings
TAMU Turbo Show 1976 Metal Diaphragm Coupling Performance Michael M. Calistrat 117 Couplings
TAMU Turbo Show 1976 Axial Vibration Characteristics of Metal-Flexing Couplings Fred K. Landon, Louis F. Counter 125 Couplings
TAMU Turbo Show 1976 Balancing of Multimass Flexible Rotors E. J. Gunter, L. E. Barrett, P. E. Allaire 133 Balancing
TAMU Turbo Show 1976 Field Testing of Compressors Meherwan P. Boyce, Richard D. Bayley, Vankayalapati Sudhakar, Vijayvardhan Elchuri 149 Centrifugal Compressors; Testing
TAMU Turbo Show 1977 Development of Turbomachinery Industry in Japan Ichiro Watanabe 1 Centrifugal Compressors; Gas Turbines
TAMU Turbo Show 1977 Torsional Vibration of Machine Systems Ronald L. Eshleman 13 Condition Monitoring; Rotordynamics
TAMU Turbo Show 1977 Machinery Monitoring Update V. Ray Dodd 23 Condition Monitoring
TAMU Turbo Show 1977 High Efficiency Fluid Film Thrust Bearings for Turbomachinery Bernard S. Herbage 33 Bearings
TAMU Turbo Show 1977 Dynamic Characteristics of Fluid-Film Bearings Wilbur Shapiro, Richard Colsher 39 Bearings; Rotordynamics
TAMU Turbo Show 1977 Rejuvenation of Used Turbine Blades by Hot Isostatic Processing Gary VanDrunen, Joseph Liburdi 55 Gas Turbines
TAMU Turbo Show 1977 Development and Testing of a New High Flow Centrifugal Pipeline Booster Robert H. Meier, Robert N. Schiller 61 Centrifugal Compressors
TAMU Turbo Show 1977 Compressor Drive Turbines of High Efficiency and Great Operational Safety Klaus Körner 75 Steam Turbines
TAMU Turbo Show 1977 High-Speed Gear Vibration and Noise Experience Norman E. Bruce 85 Gears
TAMU Turbo Show 1977 Turbine Rotors Whirl After Dynamically Stable Designs Are Updated Fred L. VanLaningham 91 Steam Turbines
TAMU Turbo Show 1977 Design of Support Structures for Elevated Centrifugal Machinery, The Marvin Lisnitzer, Donald C. Chang, L. William Abel 99 Foundations
TAMU Turbo Show 1977 Repair and Rehabilitation of Turbomachinery Foundations E. M. Renfro 107 Foundations
TAMU Turbo Show 1977 Centrifugal and Axial Flow Fan Applications and Design Criteria I. Howitt 113 Fans
TAMU Turbo Show 1977 Dynamic Simulation of Centrifugal Compressor Systems R. A. Stanley, W. R. Bohannan 123 Centrifugal Compressors
TAMU Turbo Show 1977 High Speed Gears—Design and Application James R. Partridge 133 Gears
TAMU Turbo Show 1977 Evaluation of Liquid Film Seals, Associated Systems and Process Considerations Gerald Lesiecki 145 Compressor Seals
TAMU Turbo Show 1977 Mechanical Contact Shaft Seal Richard A. Lewis 149 Compressor Seals
TAMU Turbo Show 1977 Discussion of Turbine and Compressor Sealing Devices and Systems, A Robert J. Schmal 153 Compressor Seals
TAMU Turbo Show 1977 Mechanical Seal Application—A User s Viewpoint John M. Eeds, James H. Ingram, Shannon T. Moses 171 Pump Seals
TAMU Turbo Show 1977 Fluid Film Bearings—Fundamentals and Design Criteria and Pitfalls Stanley Abramovitz 189 Bearings
TAMU Turbo Show 1977 Principles of Fluid Film Bearing Design and Application Anthony J. Leopard 207 Bearings
TAMU Turbo Show 1978 Planning Turbomachinery Overhauls and Documenting the Results John D. Houghton 1 Maintenance
TAMU Turbo Show 1978 Electromagnetic Shaft Currents and Demagnetization on Rotors of Turbines and Compressors John S. Sohre, Paul I. Nippes 13 Shaft Currents
TAMU Turbo Show 1978 State of the Art of High Speed Overhung Centrifugal Compressors for the Process Industry, The Hans Pennink 35 Centrifugal Compressors
TAMU Turbo Show 1978 Design Automation of Centrifugal Compressors Tadashi Kaneki, Eiji Yokoyama 47 Centrifugal Compressors
TAMU Turbo Show 1978 High Speed and Large Capacity Compressor-Driving Turbines for Chemical Plants Makoto Teramoto, Kazuso Katayama, Masanori Fujimuru 59 Steam Turbines
TAMU Turbo Show 1978 Investigation of the Flexural Vibration Behavior of Slender Rotors in Drum-Type Condensing Turbines, An Rolf Sparmann 71 Steam Turbines
TAMU Turbo Show 1978 Practical Considerations for a Rated Speed Shop Balance Edward A. Bulanowski, Jr. 87 Balancing
TAMU Turbo Show 1978 Compressor Response to Synchronous Motor Startup Gerald K. Mruk 95 Electric Motors
TAMU Turbo Show 1978 Subsynchronous Vibration in a Large Water Flood Pump James E. Corley 103 Pumps; Rotordynamics; Vibration Monitoring
TAMU Turbo Show 1978 Transient Analyses of Synchronous Motor Trains Fred R. Szenasi, Walter W. VonNimitz 111 Condition Monitoring; Electric Motors
TAMU Turbo Show 1978 Turbomachinery Problems—Lube and Seal System Revisited Royce N. Brown 119 Lubrication Systems
TAMU Turbo Show 1978 Particular Problems of Steam Turbine Lubrication Walter E. Enz, Alfred Häusermann 125 Lubrication Systems
TAMU Turbo Show 1978 Role of Hydraulic Balance in Mechanical Pump Seals, The Gordon S. Buck, Jr. 133 Pump Seals
TAMU Turbo Show 1978 Using Modified Acoustic Emission Techniques for Machinery Condition Surveillance Heinz P. Bloch, Robert W. Finley 139 Condition Monitoring
TAMU Turbo Show 1978 Improving Cooling Tower Fan System Efficiencies Robert C. Monroe 159 Fans
TAMU Turbo Show 1978 Operating Characteristics of Gear-Type Couplings, The Gerhardt Pahl 167 Couplings
TAMU Turbo Show 1978 Plant Lubrication Allen M. Clapp 177 Lubrication Systems
TAMU Turbo Show 1978 Lubrication Systems for Turbomachinery Fredrick B. Wilcox 189 Lubrication Systems
TAMU Turbo Show 1979 Fatigue Failures of Compressor Impellers and Resonance Excitation Testing Fred L. VanLaningham, Dave E. Wood 1 Centrifugal Compressors
TAMU Turbo Show 1979 Maintenance Techniques for Turbomachinery William E. Nelson 11 Maintenance
TAMU Turbo Show 1979 Review of Design Analysis Methods for a Horizontal End Suction Centrifugal Pump, A Robert C. Cherry 21 Pumps
TAMU Turbo Show 1979 Effects of Fluid-Filled Clearance Spaces on Centrifugal Pump and Submerged Motor Vibrations Henry F. Black 29 Pumps; Rotordynamics
TAMU Turbo Show 1979 Design and Full Load Testing of a High Pressure Centrifugal Natural Gas Injection Compressor Vijay K. Sood 35 Centrifugal Compressors
TAMU Turbo Show 1979 Selection and Design of Tilting Pad and Fixed Lobe Journal Bearings for Optimum Turborotor Dynamics John C. Nicholas, R. Gordon Kirk 43 Bearings; Rotordynamics
TAMU Turbo Show 1979 New Vibration Criteria for High Speed Large Capacity Turbomachinery, A Kazuhiro Shiraki, Hiroshi Kanki 59 Vibration Monitoring
TAMU Turbo Show 1979 Centrifugal Compressor Labyrinth Seal Systems J. Gerhardt Torborg 71 Compressor Seals
TAMU Turbo Show 1979 Couplings—A User s Point of View Charles Zirkelback 77 Couplings
TAMU Turbo Show 1979 Air Filtration and Sound Control Systems for Gas Turbines—The State of the Art Fritz P. Lages III 83 Filtration; Gas Turbines
TAMU Turbo Show 1979 Review of the Industrial Development and Usage of Electronic Governors, A Peter E. Jenkins 95 Governors
TAMU Turbo Show 1979 Mechanical Drive Turbine Control Systems for the 1980s Anthony J. Rossi 109 Governors
TAMU Turbo Show 1979 Design, Performance and Operational Characteristics of a 6500 Horsepower High Performance Industrial Gas Turbine James R. Strother 121 Gas Turbines
TAMU Turbo Show 1979 API Organization and Mechanical Equipment Specifications John G. Housman 133 Specifications
TAMU Turbo Show 1979 Principles of Turbomachinery Bearings James D. McHugh 135 Bearings
TAMU Turbo Show 1980 Hydraulically Fitted Hubs, Theory and Practice Michael M. Calistrat 1 Couplings
TAMU Turbo Show 1980 Failure Analysis and Repair Techniques for Turbomachinery Gears Thomas C. Glew 11 Gears
TAMU Turbo Show 1980 High Speed Balancing Procedures Robert Ehrich 25 Balancing
TAMU Turbo Show 1980 Unique Fan Vibration Problems: Their Causes and Solutions Donald R. Smith, Harold R. Simmons 33 Fans
TAMU Turbo Show 1980 Lateral Vibration Reduction in High Pressure Centrifugal Compressors Rudolf Jenny, Hans R. Wyssmann 45 Centrifugal Compressors; Rotordynamics
TAMU Turbo Show 1980 Analysis of Surge, The Ross Sentz 57 Centrifugal Compressors
TAMU Turbo Show 1980 Sulfidation and Its Inhibition in Turbomachinery M. A. DeCrescente 63 Gas Turbines
TAMU Turbo Show 1980 Using a "Soundtube" to Measure Noise of Structural Sources in High Background Noise Environments James T. Rainey, Frank Kushner 69 Noise
TAMU Turbo Show 1980 Vibration Problems of Large Vertical Pumps and Motors James E. Corley 75 Condition Monitoring; Rotordynamics
TAMU Turbo Show 1980 Pump Energy Conservation Techniques J. Cary Cone 83 Pumps
TAMU Turbo Show 1980 Geothermal Power and Problems T. E. McIlraith 105 Energy
TAMU Turbo Show 1980 Laser—As Used in Alignment, The Alastair J. Campbell 121 Alignment
TAMU Turbo Show 1980 Total Alignment Can Reduce Maintenance and Increase Reliability V. Ray Dodd 123 Alignment
TAMU Turbo Show 1980 Benchmark Gauges for Hot Alignment of Turbomachinery Jack N. Essinger 127 Alignment
TAMU Turbo Show 1980 Instrumental Couplings: The What, the Why and the How of the Indikon Hot-Alignment Measuring System Albert E. Finn 135 Alignment
TAMU Turbo Show 1980 Alignment Using Water Stands and Eddy Current Proximity Probes Charles Jackson 137 Alignment
TAMU Turbo Show 1980 Reverse-Indicator Alignment and Related Subjects Malcolm G. Murray, Jr. 145 Alignment
TAMU Turbo Show 1980 Dynamic Balancing Randall L. Fox 151 Balancing
TAMU Turbo Show 1980 Establishing Your Own Field Balancing Group Kevin Z. Witwer 187 Balancing
TAMU Turbo Show 1981 Stall, Stage Stall, and Surge David Japikse 1 Centrifugal Compressors
TAMU Turbo Show 1981 Measuring the Thermodynamic Performance of Multistage Compressors Operating on Mixed Hydrocarbon Gases Nazim S. Nathoo, William G. Gottenberg 15 Centrifugal Compressors
TAMU Turbo Show 1981 Design of Journal Bearings for Rotating Machinery Paul E. Allaire, Ronald D. Flack 25 Bearings; Rotordynamics
TAMU Turbo Show 1981 Field Experience and Solution of a Fractional Frequency Vibration Problem on a High Speed Centrifugal Compressor Anthony B. Crease 47 Bearings; Centrifugal Compressors; Rotordynamics
TAMU Turbo Show 1981 Four Compressor Trains of a Large Ethylene Plant—Design, Audit, Testing and Commissioning Charles Jackson 55 Centrifugal Compressors
TAMU Turbo Show 1981 Experimental Investigation of Balancing Flexible Rotors in Large Motors and Generators William H. Miller 73 Balancing; Electric Motors
TAMU Turbo Show 1981 Large Adjustable Speed Drives and Their Application to a High Speed Centrifugal Compressor Charles P. LeMone 81 Electric Motors
TAMU Turbo Show 1981 Frequency Convertors for Starting and Speed Regulations of AC Motors for Turbomachine Applications Kjell Frank 87 Electric Motors
TAMU Turbo Show 1981 Flow Recirculation in Centrifugal Pumps Warren H. Fraser 95 Pumps
TAMU Turbo Show 1981 Realistic Design Specifications Increase Pump Reliability Thomas R. Morton, Gary L. Olin 101 Pumps
TAMU Turbo Show 1981 Practical Guide to In-Place Balancing Randall L. Fox 113 Balancing
TAMU Turbo Show 1981 How to Install Maintainable Bearing Temperature Sensors Howard Maxwell 131 Bearings
TAMU Turbo Show 1981 Improved Method for Calculating Critical Speeds and Rotordynamic Stability of Turbomachinery Brian T. Murphy, John M. Vance 141 Rotordynamics
TAMU Turbo Show 1981 Measure Power by the Simplest Method and Use for Onstream Computer Monitoring William A. Clark 151 Condition Monitoring
TAMU Turbo Show 1981 Aspects of Field Performance Testing, Some William G. Gottenberg 155 Condition Monitoring
TAMU Turbo Show 1981 Field Testing of Centrifugal Compressors James W. Hunt 157 Condition Monitoring
TAMU Turbo Show 1981 Field Performance Testing to Improve Compressor Reliability Terryl Matthews 165 Condition Monitoring
TAMU Turbo Show 1981 Guidelines for Performance Testing Centrifugal Compressor Fred L. VanLaningham 169 Condition Monitoring
TAMU Turbo Show 1981 API 671—Couplings—What is the Impact on the User? Royce N. Brown 175 Coupings
TAMU Turbo Show 1981 Magnetism in Turbomachinery Paul I. Nippes 183 Shaft Currents
TAMU Turbo Show 1981 Electromagnetic Shaft Current Problems—A Users Viewpoint Bernard W. Sandner 191 Shaft Currents
TAMU Turbo Show 1981 Electromagnetic Shaft Current Control John S. Sohre 199 Shaft Currents
TAMU Turbo Show 1981 Electromagnetic Shaft Currents in Ammonia Plant—Turbomachinery at CF Industries, Inc. Lester E. Sutherland 201 Shaft Currents
TAMU Turbo Show 1982 Application of Recent Rotor Dynamics Developments to Mechanical Drive Turbines William J. Caruso, Bruce E. Gans, William G. Catlow 1 Rotordynamics
TAMU Turbo Show 1982 Rotor Dynamics Analysis and Bearing Optimization Study of a 3,800 HP Steam Turbine Dana J. Salamone 19 Rotordynamics
TAMU Turbo Show 1982 Steam Turbine Blade Options: How to Specify or Upgrade Helmut G. Naumann 29 Steam Turbines
TAMU Turbo Show 1982 Performance Improvement of Mechanical Drive Steam Turbines Hisakuni Takenaga, Kazuso Katayama, Kazuo Iida 51 Steam Turbines
TAMU Turbo Show 1982 Abradable Seals in Turbomachinery William G. Hoppock, Joseph A. Silvaggio, Jr., Kenneth G. Van Bramer 61 Compressor Seals
TAMU Turbo Show 1982 New Developments in Centrifugal Compressors John D. Halloran 69 Centrifugal Compressors
TAMU Turbo Show 1982 Aerothermal-Mechanical Health Monitoring and Diagnostics of Turbo-Compressor Sets Meherwan P. Boyce, Cyrus B. Meher-Homji 75 Condition Monitoring
TAMU Turbo Show 1982 Residual Oil Burning Experience at the Putman Plant of Florida Power & Light Company William J. Hensler 95 Gas Turbines
TAMU Turbo Show 1982 Efficiency: The Silent Partner of Machine Performance David Japikse 105 Centrifugal Compressors
TAMU Turbo Show 1982 Shop Full-Load Testing of Centrifugal Compressors Angelo Maretti, Mauro Giovannini, Pierluigi Nava 113 Centrifugal Compressors
TAMU Turbo Show 1982 Advanced Technologies for Turbomachinery Systems—An Overview Melvin J. Hartmann 123 Gas Turbines
TAMU Turbo Show 1982 Calculation and Verification of Torsional Natural Frequencies for Turbomachinery Equipment Strings, The Roy E. Mondy, John Mirro 151 Condition Monitoring; Rotordynamics
TAMU Turbo Show 1982 Continuous Monitoring Systems for High Speed Gearing John S. Mitchell 157 Gears
TAMU Turbo Show 1982 Prerotation and Fluid Recirculation in the Suction Pipe of Centrifugal Pumps F. A. E. Breugelmans, M. Sen 165 Pumps
TAMU Turbo Show 1982 Two-Phase Mechanical Face Seal Operation: Experimental and Theoretical Observations Alan O. Lebeck, Bing-Ching Chiou 181 Compressor Seals
TAMU Turbo Show 1982 Inlet Flow and Aspects of Cavitation in Centrifugal Impellers Masao Oshima 189 Pumps
TAMU Turbo Show 1982 Compressor and Turbine Shaft Repair: A User s Viewpoint Norman E. Bruce 197 Repair
TAMU Turbo Show 1982 Material Coating by the Detonation Gun Process Walter Wolentarski 207 Repair
TAMU Turbo Show 1982 Performance Improvements of a Westinghouse W-171 Gas Turbine by Coating Axial Compressor Blading Bruce N. Tilley 217 Axial Compressor; Centrifugal Compressors
TAMU Turbo Show 1983 Design and Calculation Methods for High-Speed Gears of Advanced Technology Manfred Hirt 1 Gears
TAMU Turbo Show 1983 Mechanical Seals for High Face Speed Applications Wolfgang Schuebl 9 Pump Seals
TAMU Turbo Show 1983 Low Frequency Buckets for Industrial Steam Turbines Firm L. Weaver 15 Steam Turbines
TAMU Turbo Show 1983 Guidelines for Reliable Extension of Turbine Blade Life Joseph Liburdi, James Wilson 21 Gas Turbines
TAMU Turbo Show 1983 Structural Integrity of Large Steam Turbine Rotors Gary W. Rogers, Clifford H. Wells, Duane P. Johnson 31 Steam Turbines
TAMU Turbo Show 1983 Check Valves for Compressor Protection—A User s View Frank Andrews, Harold B. Carrick 45 Centrifugal Compressors
TAMU Turbo Show 1983 On Stream Solution of a Prototype 8000 HP Motor Instability Problem Perry C. Monroe, Jr., Dana J. Salamone 53 Electric Motors
TAMU Turbo Show 1983 Technical Approach to the Maintenance and Overhaul of Gas Turbines, A Chester D. Hall 73 Maintenance; Gas Turbines
TAMU Turbo Show 1983 Rotor Dynamics Modification of an Eight Stage Compressor for Safety/Reliability Improvement Francis H. Kludt, Dana J. Salamone 81 Bearings; Rotordynamics
TAMU Turbo Show 1983 Design, Testing and Commissioning of a Synchronous Motor-Gear-Axial Compressor Charles Jackson, Malcolm E. Leader 97 Axial Compressor
TAMU Turbo Show 1983 Generalized and Simplified Transient Torque Analysis for Synchronous Motor Drive Trains, A H. Ming Chen, Donald W. McLaughlin, Stanley B. Malanoski 115 Condition Monitoring; Electric Motors
TAMU Turbo Show 1983 Impact of Swing Conditions on Turbine Design, The Edward J. Finck 121 Steam Turbines
TAMU Turbo Show 1983 Industrial Cogeneration System Application Considerations John M. Kovacik 129 Cogeneration
TAMU Turbo Show 1983 Performance of Apiate Diester Synthetic Lubricants in the Hydrodynamic Regime Nigel H. New, Richard H. Schmaus 139 Lubrication Systems
TAMU Turbo Show 1983 Practical Aspects of Centrifugal Compressor Surge and Surge Control Meherwan P. Boyce, William R. Bohannan, Royce N. Brown, John R. Gaston, Cyrus B. Meher-Homji, Robert H. Meier, Norbert E. Pobanz 147 Centrifugal Compressors
TAMU Turbo Show 1984 Overview of Cogeneration Technology—Design, Operation and Maintenance, An Meherwan P. Boyce, Cyrus B. Meher-Homji, Alfred B. Focke 3 Cogeneration
TAMU Turbo Show 1984 Steam Turbine Efficiency Improvement Application and Conversion, A Bruce Weathersby, Andrew P. Mahon, Stephen Chesmejef 25 Steam Turbines
TAMU Turbo Show 1984 Design, Control and Startup Features of Three Parallel-Working Propane Compressors Each Having Three Stage Groups Wilfred Blotenberg, Hans-Otto Jeske, Heinrich Voss 39 Centrifugal Compressors
TAMU Turbo Show 1984 Empirical Solution to an Anti-Surge Control Problem, An Stephen R. Locke 51 Centrifugal Compressors
TAMU Turbo Show 1984 Variable Speed Fluid Couplings Driving Centrifugal Compressors and Other Centrifugal Machinery Gunther H. Peikert 59 Variable Speed Couplings
TAMU Turbo Show 1984 Improved Method to Determine the Scoring Resistance of High Power High Speed Gearing, An Manfred Hirt 67 Gears
TAMU Turbo Show 1984 Analysis of Service Failures Paul S. Gupton 75 Metallurgy
TAMU Turbo Show 1984 Metallurgical Failure Analysis—What, Why and How Edward L. Creamer 87 Metallurgy
TAMU Turbo Show 1984 Manufacturers World of Coupling Potential Unbalance, The Jon R. Mancuso 97 Couplings
TAMU Turbo Show 1984 Critical Speeds of Turbomachinery—Computer Predictions Vs. Experimental Measurements John M. Vance, Brian T. Murphy, Harley A. Tripp 105 Rotordynamics
TAMU Turbo Show 1984 Temperature Measurements in Fluid Film Bearings Denis R. Garner, Anthony J. Leopard 133 Bearings
TAMU Turbo Show 1984 Development of High Specific Speed Mixed Flow Compressors Fumikata Kano, Yoshiteru Fukao, Takafumi Shirakami 139 Centrifugal Compressors
TAMU Turbo Show 1984 Lubrication and Seal Oil Systems Roy J. Salisbury, Ricardo Stack, Marc J. Sassos 151 Lubrication Systems
TAMU Turbo Show 1984 Journal Bearing Design Types and Their Applications to Turbomachinery Dana J. Salmone 179 Bearings
TAMU Turbo Show 1984 Coupling Applications for Special Purpose Machinery—Multiple Flexible Membrane Types Richard E. Ruckstuhl 193 Couplings
TAMU Turbo Show 1984 Application of Single Membrane Type Flexible Power Transmission Couplings Merle E. Crane, Jr. 199 Couplings
TAMU Turbo Show 1984 Torsional-Damping—Transient and Steady State Royce N. Brown 203 Condition Monitoring; Couplings
TAMU Turbo Show 1985 Rotordynamic Stability—A Simplified Approach Carroll G. Stroh 3 Rotordynamics
TAMU Turbo Show 1985 Subsynchronous Vibration Problems in High-Speed, Multistage Centrifugal Pumps Ian C. Massey 11 Pumps; Rotordynamics
TAMU Turbo Show 1985 Review of Fundamental Two Pole Induction Motor Mechanics Cletus A. Corey 17 Electric Motors
TAMU Turbo Show 1985 Failure of Turbomachinery Components Paul Lowden, Joseph Liburdi 23 Metallurgy
TAMU Turbo Show 1985 Storage Preservation of Machinery Heinz P. Bloch 35 Preservation
TAMU Turbo Show 1985 Shop Vs. Field Corrections to Equipment Clifford P. Cook 47 Operation; Repair
TAMU Turbo Show 1985 Design of Coupling Enclosures Michael M. Calistrat, Robert E. Munyon 51 Couplings
TAMU Turbo Show 1985 Gas Lubricated Spiral Grooved Face Seal in the Process Industry, The Hans Pennink 59 Compressor Seals
TAMU Turbo Show 1985 Startup of a Large Compressor Train—Testing Verifies Design Jerry C. Swalley 65 Centrifugal Compressors
TAMU Turbo Show 1985 Radial and Thrust Bearing Practices with Case Histories Charles Jackson 73 Bearings
TAMU Turbo Show 1985 Wind Energy: Applying New Technology to an Old Idea Kent L. Fickett 89 Energy; Wind Turbines
TAMU Turbo Show 1985 Practical Approach to Understanding Steels, Their Alloying, Heat Treatment and Surface Hardening, A Paul S. Gupton 103 Metallurgy
TAMU Turbo Show 1986 Testing and Startup Experience with Rotating Equipment at Nation s First Commercial Scale Coal Gasification Plant S. Paul Mohan 1 Energy
TAMU Turbo Show 1986 On the Manufacture of Impellers for Turbomachinery Klaus Boddenberg 9 Centrifugal Compressors
TAMU Turbo Show 1986 Oil Seal Dynamics: Considerations for Analysis of Centrifugal Compressors R. Gordon Kirk 25 Rotordynamics; Compressor Seals
TAMU Turbo Show 1986 Effects of High Pressure Oil Seals on the Rotordynamic Response of Centrifugal Compressors Thomas J. Cerwinske, William E. Nelson, Dana J. Salamone 35 Rotordynamics; Compressor Seals
TAMU Turbo Show 1986 Balancing of Integral Gear-Driven Centrifugal Compressors Hatto Schneider 53 Balancing; Centrifugal Compressors
TAMU Turbo Show 1986 Vibration Analysis of Vertical Pumps Donald R. Smith, Glenn M. Woodward 61 Condition Monitoring; Rotordynamics
TAMU Turbo Show 1986 Improving Critical Speed Calculations Using Flexible Bearing Support FRF Compliance Data John C. Nicholas, John K. Whalen, Sean D. Franklin 69 Critical Speed; Rotordynamics
TAMU Turbo Show 1986 Dynamic Analysis of an 8,000 HP Steam Turbine Operating Near Its Second Critical Speed Bill Majovsky, Dana J. Salamone 79 Rotordynamics
TAMU Turbo Show 1986 Retrofitting a Topping Turbine for Performance and Mechanical Improvement Vincent S. Wagner, Jr. 93 Steam Turbines
TAMU Turbo Show 1986 Retrofit Installation of a Boiler Feed Pump Hydraulic Coupling Merwin W. Jones, Scott R. Taylor, Bernard S. Herbage 101 Pumps
TAMU Turbo Show 1986 Development and Implementation of an Expert System to Diagnose Motor Vibration Problems James E. Corley, Gary D. Darby 111 Electric Motors; Rotordynamics
TAMU Turbo Show 1986 Operator s Critical Need for Quality in Turbomachinery, The Richard M. Dubner 119 Operation
TAMU Turbo Show 1986 Detection of Rotor Cracks Donald E. Bently, Agnes Muszynska 129 Condition Monitoring; Rotordynamics
TAMU Turbo Show 1986 Shop Balancing of Turbomachinery Rotors John R. East, E. Bruce Williams 147 Balancing
TAMU Turbo Show 1986 Design Audits J. C. Wachel 153 Design Audits
TAMU Turbo Show 1987 Application of Ion-Plated Cr-TiN Multilayer Coating to Steam Turbine Blades Ryuichiro Ebara, Hiroshi Nakajima, Toshihiko Odohira, Tetsuyoshi Wada, Masaaki Hatano 3 Materials; Steam Turbines
TAMU Turbo Show 1987 Compressor Performance Modelling and Monitoring John B. Duggan 9 Centrifugal Compressors
TAMU Turbo Show 1987 Conversion of a 19,000 HP Propylene Compressor from Steam Turbine to Electric Motor with Geared Variable Speed Turbo Coupling Franz-Klaus Henschel, Walter Rappold 23 Fluid Couplings; Electric Motors
TAMU Turbo Show 1987 New Solutions in the Process Industry—Application of Six-Stage Integrally Geared Centrifugal Compressors Ernst Rothstein 31 Centrifugal Compressors
TAMU Turbo Show 1987 Experience with Periodic Vibration Monitoring in Fossil Power Stations Kenneth R. Piety, E. Forrest Pardue, Ernest P. Phillips 41 Vibration Monitoring
TAMU Turbo Show 1987 Electric Shaft Currents in Turbomachinery John M. Vance, Alan B. Palazzolo, Fouad Y. Zeidan 51 Shaft Currents
TAMU Turbo Show 1987 Subsynchronous Vibration Problem and Solution In Multistage Centrifugal Compressor Paul E. Allaire, Carroll G. Stroh, Ronald D. Flack, John A. Kocur, Jr., Lloyd E. Barrett 65 Centrifugal Compressors; Rotordynamics; Vibration Monitoring
TAMU Turbo Show 1987 Retrofit of Gas Lubricated Face Seals in a Centrifugal Compressor, A John A. Kocur, Jr., John P. Platt, Jr., Larry G. Shabi 75 Rotordynamics; Compressor Seals
TAMU Turbo Show 1987 Revamp of Turbocompressors Walter Aicher, Samuel Schnyder 85 Axial Compressor; Centrifugal Compressors
TAMU Turbo Show 1987 Revamping the Air Compressor in an Ammonia Plant William G. Hoppock, Larry L. Fisher 93 Centrifugal Compressors
TAMU Turbo Show 1987 Retrofitting Gas Turbines with Computer Control Joel R. Taub, Joseph E. Armacost 99 Governors
TAMU Turbo Show 1987 Major Revamp and Retrofit of Identical Process Compressor Trains M. Donald Low III, Richard E. Nemec 105 Centrifugal Compressors
TAMU Turbo Show 1988 Application of Dry Gas Seals on a High Pressure Hydrogen Recycle Compressor Donald R. Carter 3 Compressor Seals
TAMU Turbo Show 1988 Influence of Gas Seals on Rotor Stability of a High Speed Hydrogen Recycle Compressor Kenneth E. Atkins, Robert X. Perez 9 Rotordynamics; Compressor Seals
TAMU Turbo Show 1988 Solution of Subsynchronous Vibration Problems in Radial Flow High-Speed Turbines Heiko D. Sandstede, Klaus Reischl, Martin L. Leonhard 19 Condition Monitoring; Rotordynamics
TAMU Turbo Show 1988 Online Diagnostics of Rotating Machinery Kim Alan Lovejoy 29 Condition Monitoring
TAMU Turbo Show 1988 Vacuum Distillation Methods for Lube Oils Increase Turbomachinery Reliability Mark A. Adams, Heinz P. Bloch 41 Lubrication Systems
TAMU Turbo Show 1988 Water Contamination of Steam Turbine Lube Oil— How to Avoid it Willam L. Coleman 51 Lubrication Systems
TAMU Turbo Show 1988 Experience with Online Condition Monitoring System Refah R. Unsal, Meherwan P. Boyce 57 Condition Monitoring
TAMU Turbo Show 1988 Turbine Protection System Performance Margaret C. Campbell 67 Condition Monitoring
TAMU Turbo Show 1988 Operating Experience with Improved Steam Turbine Packing Rings Steve Williams, Ronald E. Brandon 77 Steam Turbines
TAMU Turbo Show 1988 Turbine Generator Life Assessment/Extension Donald R. McCann, H. R. Jhansale, James L. Anderson 85 Steam Turbines
TAMU Turbo Show 1988 Safe Diagram—A Design and Reliability Tool for Turbine Blading Murari P. Singh, John J. Vargo, Donald M. Schiffer, James D. Dello 93 Condition Monitoring; Steam Turbines
TAMU Turbo Show 1988 Improving Plant Economy Through Retrofit and Maintenance of Compressors Karl H. Nissler 103 Centrifugal Compressors
TAMU Turbo Show 1988 Emergency Turbine Repair Procedures Peter P. Franks, Jr., Ben Eads 115 Steam Turbines
TAMU Turbo Show 1988 Large Motor Specification and Selection William H. Miller 123 Electric Motors
TAMU Turbo Show 1988 Dry Gas Compressor Seals Piyush Shah 133 Compressor Seals
TAMU Turbo Show 1988 Full Fluid Film Face Seals Peter Lytwyn 141 Pump Seals
TAMU Turbo Show 1988 Turbomachinery Health Measurement Application and Misapplication Malcolm E. Leader 147 Condition Monitoring
TAMU Turbo Show 1988 Nondestructive Testing of Turbomachinery Components Paul S. Gupton 161 Metallurgy
TAMU Turbo Show 1989 Heavy Shell Castings—Design/Operation and Repairs Criteria Mark T. Breslin 3 Materials; Repair
TAMU Turbo Show 1989 Materials for Centrifugal Compressors—A Progress Report Joseph A. Cameron 9 Materials
TAMU Turbo Show 1989 Practical Applications of Rotordynamics, Bearing Design, Mechanical Analysis, and Vibration Diagnostics to Design Problems of Rotating Machinery in Operation John Mirro 23 Rotordynamics
TAMU Turbo Show 1989 Operating Turbomachinery on or Near the Second Critical Speed in Accordance with API Specifications John C. Nicholas 47 Balancing; Rotordynamics
TAMU Turbo Show 1989 Fouling of Axial Flow Compressors—Causes, Effects, Detection, and Control Cyrus B. Meher-Homji, Alfred B. Focke, M. Byron Wooldridge 55 Axial Compressor
TAMU Turbo Show 1989 Reapplication of an Induction Steam Turbine to Extraction Cogeneration Service Richard E. Nemec, Barnett F. McLaughlin 77 Reapplication
TAMU Turbo Show 1989 Maximizing an Ethylene Plant s Turbomachinery Reliability John R. Dugas, Jr. 85 Balancing; Maintenance; Rotordynamics
TAMU Turbo Show 1989 Maximizing Compressor Efficiency While Maintaining Reliability D. Fred Marshall, Joseph A. Cotroneo 91 Centrifugal Compressors
TAMU Turbo Show 1989 Solid Couplings with Flexible Intermediate Shafts for High Speed Turbocompressor Trains Heinrich Lorenzen, Ernst A. Niedermann, Werner Wattinger 101 Couplings
TAMU Turbo Show 1989 Reapplication of Turbomachinery Michael Tighe, Juan A. Suarez 111 Reapplication
TAMU Turbo Show 1989 Introduction and Case History Review of Active Magnetic Bearings, An David A. Weise, Frank D. Pinckley 121 Bearings
TAMU Turbo Show 1989 Setting Vibration Criteria for Turbomachinery James D. McHugh 127 Specifications; Vibration Monitoring
TAMU Turbo Show 1989 Application of Flexible Couplings for Turbomachinery, The Jon R. Mancuso, C. Barney Gibbons, Robert E. Munyon 141 Couplings
TAMU Turbo Show 1989 Advanced Turbomachinery Health Monitoring—Part II Malcolm E. Leader 167 Vibration Monitoring
TAMU Turbo Show 1990 Troubleshooting High Speed Couplings Eddie L. Schneider 3
TAMU Turbo Show 1990 An Independent Refiner's Approach—Practical Solutions to Complex Gear Problems John B. Cary 9
TAMU Turbo Show 1990 Gas Turbine Control Systems Incorporating Condition Monitoring and Fault Tolerance Gordon L. Muster II, Michael Feinstein 21
TAMU Turbo Show 1990 Efficient Part Load Combined Cycle Operations James O. Stephens, David A. Little, Phillip J. Hunt, Rick Stanaland 31
TAMU Turbo Show 1990 Recent Case Histories with Coupling Enclosures Michael M. Calistrat 37
TAMU Turbo Show 1990 Reliability Criteria for Turbine Shaft Based on Coupling Type—Geared to Have Flexibility Murari P. Singh, Charles M. Ramsey 43
TAMU Turbo Show 1990 Retrofit, Upgrade, and Demothball of Two Centrifugal Compressor Trains Charles Jackson 51
TAMU Turbo Show 1990 Retrofitting Turbomachinery with High Performance Flexible Dry Couplings Christian C. Wolford 63
TAMU Turbo Show 1990 Understanding the Vibration Forces in Induction Motors Michael J. Costello 67
TAMU Turbo Show 1990 Magnetic Bearings and Dry Gas Seals—A Process Compressor Application Kenneth G. Van Bramer, Charles Peter Conquergood 77
TAMU Turbo Show 1990 Energy Recovery in a Gas Distribution Station by Combination of Expanders with Planetary Gear and Optimum Single Valve Control Helmut G. H. Beer 85
TAMU Turbo Show 1990 Online Ultrasonic Monitoring of Bearing Wear Jeffrey C. Chann 91
TAMU Turbo Show 1990 Vibration Monitoring of Turbomachinery Alexander Lifson, Harold R. Simmons 101
TAMU Turbo Show 1990 Piping Vibration Analysis J. C. Wachel, Scott J. Morton, Kenneth E. Atkins 119
TAMU Turbo Show 1990 Romex—An Expert System Testbed for Turbomachinery Diagnostics David W. Lewis, Pradip N. Sheth 135
TAMU Turbo Show 1990 Troubleshooting Turbomachinery Problems Using a Statistical Analysis of Failure Data James E. Corley 149 Diagnostics
TAMU Turbo Show 1991 Specifying, Manufacturing, and Testing a Cryogenic Turboexpander Magnetic Bearing System Jigger Jumonville, Charles M. Ramsey, Frank Andrews 3
TAMU Turbo Show 1991 Rotordynamic Aspects of a New Hermetically Sealed Pipeline Compressor Joachim Schmied 11
TAMU Turbo Show 1991 Submerged Arc Weld Restoration of Steam Turbine Rotors Using Specialized Welding Techniques Richard A. LaFave 19
TAMU Turbo Show 1991 Repair Severely Damaged Rotor by Submerged Arc Welding Jim Heeter 35
TAMU Turbo Show 1991 Recent Experience with Large Liquid Injected Rotary Screw Process Gas Compressors Heinz P. Bloch, Pierre W. Noack 43
TAMU Turbo Show 1991 Adaptation of a Propylene Refrigeration Compressor with Dry Gas Seals John R. Dugas, Jr., Bich X. Tran, James F. Southcott 57
TAMU Turbo Show 1991 Shaft Riding Brushes to Control Electric Stray Currents John S. Sohre 63
TAMU Turbo Show 1991 Investigation of Suitability of Abradable Seal Materials for Application in Centrifugal Compressors and Steam Turbines, The Phillip Dowson, Stephen L. Ross, Carl Schuster 77
TAMU Turbo Show 1991 Fan Laws, the Use and Limits in Predicting Centrifugal Compressor Off Design Performance Royce N. Brown 91
TAMU Turbo Show 1991 Centrifugal Compressor Performance Enhancement through the Use of a Single Stage Development Rig James M. Sorokes, John P. Welch 101
TAMU Turbo Show 1991 Do It Right the First Time—A Review of an Ethylene Plant Turbomachinery Commissioning Test Kazim Akhtar, W. E. Forsthoffer 113
TAMU Turbo Show 1991 General Purpose Steam Turbine Reliability John B. Cary 123
TAMU Turbo Show 1991 Standardized Integrally Geared Turbomachines— Tailor Made for the Process Industry Udo Fingerhut, Ernst Rothstein, Gerard Sterz 131
TAMU Turbo Show 1991 New Technology on High Performance and Reliability of Mechanical Drive Steam Turbines Tomoyoshi Sasaki, Shigeki Morii, Hisakuni Takenaga, Masanori Tsutsumi 145
TAMU Turbo Show 1991 Fluid Film Bearing Fundamentals and Failure Analysis Fouad Y. Zeidan, Bernard S. Herbage 161
TAMU Turbo Show 1991 Procedure for Selecting and Evaluating a Special Purpose Motor Clifford P. Cook, Michael J. Costello 187
TAMU Turbo Show 1991 Turbomachinery Balancing Considerations John R. East 209
TAMU Turbo Show 1992 Dry Screw Compressors in Process Gas Applications Including Maintenance Considerations Glen B. Nordquist, Peter A. Bielskus, Russ Clayton 3 Screw Compressors; Maintenance; Rotordynamics
TAMU Turbo Show 1992 Twenty Years of Experience with a Modular Design System for Centrifugal Process Compressors Klaus Lüdtke 21 Centrifugal Compressors
TAMU Turbo Show 1992 Rotor Bearing and Shaft Dynamics Redesign of a Double-Overhung Turboexpander for Reliability Improvement Thomas R. Davidson, Dana J. Salamone, Edgar J. Gunter 35 Rotordynamics; Wind Turbines
TAMU Turbo Show 1992 Flexible Pad Bearing System for a High Speed Centrifugal Compressor, A Pranabesh De Choudhury, M. Raymond Hill, Donald J. Paquette 57 Bearings; Centrifugal Compressors
TAMU Turbo Show 1992 Applying the Probabilistic Fitness-for-Service Concept for Assessing Reliability of Weld Repaired Steam Turbine Rotors Anthony A. Tipton, Murari P. Singh, C. D. Shepherd 65 Maintenance; Materials; Metallurgy; Repair; Steam Turbine;
TAMU Turbo Show 1992 Temporary Repair of a Large Axial Blast Furnace Motor-Blower as a Solution for a Steel Mill Operational Continuity Luiz F. S. Mendes, Alberto Azuma, Ernesto J. Meduna 73 Motors; Repair
TAMU Turbo Show 1992 Gear Coupling Misalignment Induced Forces and Their Effects on Machinery Vibration Alan B. Palazzolo, Stephen R. Locke, Michael M. Calistrat, Robert W. Clark, Jr., Akram Ayoub, Dan Calistrat, Punan Tang 83 Bearings; Couplings; Rotordynamics
TAMU Turbo Show 1992 Experience with Nonstandard Coupling Application, An Edward B. Wharton, Carroll G. Stroh 97 Alignment; Couplings; Maintenance
TAMU Turbo Show 1992 Large Converter-Fed Adjustable Speed AC Drives for Turbomachines Andrej Grgic, Werner Heil, Herbert Prenner 103 Alignment; Couplings; Maintenance
TAMU Turbo Show 1992 Lateral Vibration Created by Torsional Coupling of a Centrifugal Compressor System Driven by a Current Source Drive for a Variable Speed Induction Motor James H. Hudson 113 Couplings; Electric Motors
TAMU Turbo Show 1992 Specifying Steam and Rating Conditions for Special Purpose Steam Turbines John S. Aalto 125 Specifications; Steam Turbine
TAMU Turbo Show 1992 Design, Installation, and Test of a Steam Injection System on an Early Frame 3 Gas Turbine in a Combined Cycle Pipeline Compressor Station S. Paul Mohan, Robert D. Underwood, David A. Little 137 Gas Turbines
TAMU Turbo Show 1992 Assessing Rotor Stability Using Practical Test Procedures Kenneth E. Atkins, Robert X. Perez 151 Centrifugal Compressors; Testing
TAMU Turbo Show 1992 Fundamental Understanding of Rotordynamics from a Light Rub (Bounce), A Carroll G. Stroh 161 Maintenance; Rotordynamics; Vibration Monitoring
TAMU Turbo Show 1992 Axial Air Compressors—Maintaining Peak Efficiency M. Theodore Gresh, Marc J. Sassos, Andrew Watson 173 Axial Compressors
TAMU Turbo Show 1992 Compressor Types, Classifications, and Applications David H. Robison, Peter J. Beaty 183 Axial Compressors; Centrifugal Compressors; Screw Compressors
TAMU Turbo Show 1992 Reverse Alignment—Understanding Centerline Measurement C. Richard Massey, Alastair J. Campbell 189 Alignment
TAMU Turbo Show 1992 Major Foundation Repair of a Twenty Ton Centrifugal Compressor Walter L. Garrett, Perry C. Monroe, Jr. 197 Centrifugal Compressors; Repair
TAMU Turbo Show 1993 Use of Honeycomb Seals in Stabilizing Two Centrifugal Compressors, The Fouad Y. Zeidan, Robert X. Perez, E. Morris Stephenson 3 Centrifugal Compressors
TAMU Turbo Show 1993 Comprehensive Cause Analysis of a Coupling Failure Induced by Torsional Oscillations in a Variable Speed Motor, A Harley Tripp, Don Kim, Robert Whitney 17 Variable Speed Couplings; Electric Motors
TAMU Turbo Show 1993 Shifting Critical Speeds Out of the Operating Range by Changing From Tilting Pad to Sleeve Bearings John C. Nicholas, Randall W. Moll 25 Bearings; Critical Speed; Rotordynamics
TAMU Turbo Show 1993 Reduced Shaft Stiffness Lowers Running-Speed Bearing Loads and Vibration in a Single Stage Compressor Richard W. Armentrout, Gerald E. Wilson 33 Bearings; Centrifugal Compressors; Critical Speed; Rotordynamics
TAMU Turbo Show 1993 Retrofit of a Steam Turbine with Dry Gas Seals James R. Morris, Carroll G. Stroh, James F. Southcott 45 Compressor Seals; Steam Turbines
TAMU Turbo Show 1993 Lubrication and Seal Oil Systems—Common Problems and Practical Solutions Marc J. Sassos, Mark R. Babyak, Joseph P. Zerbe, Jr. 51 Lubrication Systems
TAMU Turbo Show 1993 Safety, Application, and Service Factors as Applied to Shaft Couplings Michael M. Calistrat, William E. Nelson 65 Couplings
TAMU Turbo Show 1993 Critical Speeds and the Importance of Stiffness—A Case Study in the Design and Testing of a Large Mechanical Drive Steam Turbine to API Standard 612 Lawrence L. Bethel, Bruce E. Gans, Royce N. Brown, Richard A. Lewis 73 Critical Speed; Rotordynamics; Testing; Steam Turbines
TAMU Turbo Show 1993 Magnetic Bearing Retrofit of a High Speed, Eight Stage Coker Compressor Pranabesh De Choudhury, Andrew P. Watson, Donald R. Carter, Chet Farabaugh 81 Bearings; Centrifugal Compressors
TAMU Turbo Show 1993 Predicting and Verifying Rerated Compressor Performance Through Single Stage Scale Model and Limited Field Testing Brad Cardon, John Bartos 91 Centrifugal Compressors; Reapplication; Testing
TAMU Turbo Show 1993 Case Studies in Turbomachinery Operation and Maintenance Using Condition Monitoring Meherwan P. Boyce, George A. Gabriles, Cyrus B. Meher-Homji, A. N. Lakshminarasimha, Feroze J. Meher-Homji 101 Maintenance; Gas Turbines; Steam Turbines
TAMU Turbo Show 1993 Practical Application of CFD in the Design of Industrial Centrifugal Impellers, The James M. Sorokes 113 Centrifugal Compressors
TAMU Turbo Show 1993 Analysis of Torsional Vibrations in Rotating Machinery J. C. Wachel, Fred R. Szenasi 127 Vibration Monitoring
TAMU Turbo Show 1993 Hydraulic Removal of Coupling Hubs—Keyed and Keyless Michael M. Calistrat, James R. Morris, Robert Parker 153 Couplings
TAMU Turbo Show 1993 Principles of Operation and Performance Estimation of Centrifugal Compressors Meherwan P. Boyce 161 Centrifugal Compressors; Operation
TAMU Turbo Show 1993 Test of Process Turbocompressors Without CFC Gasses Walter Aicher 179 Centrifugal Compressors; Testing
TAMU Turbo Show 1993 Large Motor Installation and Startup William H. Miller 185 Alignment; Electric Motors
TAMU Turbo Show 1993 Baseline Mapping of Discontinuities Through Nondestructive Testing Daniel E. Coleman, Timothy A. Plesz 191 Inspection
TAMU Turbo Show 1993 Shop Balancing Charles Jackson 197
TAMU Turbo Show 1994 Recent Experiences in Full Load Full Pressure Shop Testing of a High Pressure Gas Injection Centrifugal Compressor James M. Sorokes, Mark J. Kuzdzal, Mark R. Sandberg, Gary M. Colby 3 Centrifugal Compressors; Rotordynamics; Testing
TAMU Turbo Show 1994 Considerations and Issues in the Replacement of a Centrifugal Compressor Train Donald A. Rudisel 19 Centrifugal Compressors; Foundations; Steam Turbines
TAMU Turbo Show 1994 Design, Analysis, and Testing of High Performance Bearings in a High Speed Integrally Geared Compressor Wen Jeng Chen, Fouad Y. Zeidan, Dilip Jain 31 Bearings; Centrifugal Compressors; Gears; Rotordynamics; Testing;
TAMU Turbo Show 1994 False and Misleading Sources of Vibration Albert F. Criqui1 37 Diagnostics
TAMU Turbo Show 1994 Analysis and Testing of the Leg Tilting Pad Journal Bearing—A New Design for Increasing Load Capacity, Reducing Operating Temperatures and Conserving Energy Keith Brockwell, Waldemar Dmochowski, Scan DeCamillo 43 Bearings; Energy; Lubrication Systems; Testing
TAMU Turbo Show 1994 Improving the Mechanical Reliability of a Turbine-compressor-expander Used in a Nitric Acid Manufacturing Plant Darayus Pardivala, LeEllen Phelps, Malcolm E. Leader 57 Repair
TAMU Turbo Show 1994 Take Transient Startup and Shutdown Data—Rule Number One Charles Jackson 69 Design Audits; Diagnostics; Testing
TAMU Turbo Show 1994 Use of Engineering Thermoplastics for Centrifugal Compressor Labyrinths, The John K. Whalen 81 Compressor Seals
TAMU Turbo Show 1994 Impeller Repair Techniques for Centrifugal Compressors Charles R. Clayton, Darwin Klein, Mark F. Emerick 91 Centrifugal Compressors; Inspection; Repair; Welding
TAMU Turbo Show 1994 Fatigue Damage of Steam Turbine Blade Caused by Frequency Shift Due to Solid Buildup—A Case Study Murari P. Singh, Terryl Matthews, Charles Ramsey 107 Repair; Steam Turbines
TAMU Turbo Show 1994 Baffling and Temperature Prediction of Coupling Enclosures, The Donald Carter, Martin Garvey, Joseph P. Corcoran 115 Couplings
TAMU Turbo Show 1994 Retuning a Gear Disc Profile to Eliminate High Gear Vibration James H. Hudson, Keith Rouch 125 Gears; Testing
TAMU Turbo Show 1994 Selection of Turbomachinery—Centrifugal Compressors Gary A. Ehlers 151 Centrifugal Compressors
TAMU Turbo Show 1994 Process Safety Management J. S. Arendt, David A. Walker 165
TAMU Turbo Show 1994 General Purpose Vs Special Purpose Couplings Jon Mancuso 167 Couplings
TAMU Turbo Show 1994 Tilting Pad Bearing Design John C. Nicholas 179 Bearings; Rotordynamic
TAMU Turbo Show 1994 Centrifugal Compressor Application Sizing, Selection, and Modelling Royce N. Brown, Richard A. Lewis 195 Centrifugal Compressors
TAMU Turbo Show 1994 Some Thoughts on Avoiding Metallurgical Failures Paul S. Gupton 203 Metallurgy
TAMU Turbo Show 1994 Application of High Speed and High Performance Fluid Film Bearings in Rotating Machinery Fouad Y. Zeidan, Donald J. Paquette 209 Bearings
TAMU Turbo Show 1994 Magnetic Bearing Operating Experience John Sears, Stan Uptigrove 235 Bearings
TAMU Turbo Show 1994 Vibrations in Reciprocating Machinery and Piping Systems J. C. Wachel, J. D. Tison 243 Design Audits; Diagnostics; Foundations; Maintenance; Operation;
TAMU Turbo Show 1995 Experiences in Analysis and Monitoring Compressor Performance John B. Duggan, Stephen R. Locke 3 Condition Monitoring; Diagnostics; Energy; Maintenance; Reapplication;
TAMU Turbo Show 1995 Factors and Preventive Measures Relative to the High Temperature Corrosion of Blade/Disk Components in FCC Power Recovery Turbines Phillip Dowson, Douglas M. Rishel, Norman S. Bornstein 11 Corrosions; Materials; Metallurgy; Gas Turbines; Turboexpanders;
TAMU Turbo Show 1995 Application of a Hydrostatic Pressure Lift System for Control of Variable Thrust Loads, An Essie Noori, Michael J. Harrington, David R. Stenson 27 Bearings; Maintenance; Steam Turbines
TAMU Turbo Show 1995 Tilting Pad Journal Bearing Pivot Design for High Load Applications John C. Nicholas, Karl D. Wygant 33 Bearings
TAMU Turbo Show 1995 Design and Application of a Squeeze Film Damper Bearing to a Flexible Steam Turbine Rotor, The Malcolm E. Leader, John K. Whalen, Godfrey G. Grey, Thomas D. Hess, Jr. 49 Bearings; Rotordynamics; Steam Turbines
TAMU Turbo Show 1995 Using a Damper Seal to Eliminate Subsynchronous Vibrations in Three Back-to-Back Compressors Robert L. Richards, John M. Vance, Donald J. Paquette, Fouad Y. Zeidan 59 Compressor Seals
TAMU Turbo Show 1995 Pad Temperature in High Speed, Lightly Loaded Tilting Pad Journal Bearings Stephen L. Edney 73 Bearings
TAMU Turbo Show 1995 Thermal Effects in Hydrodynamic Journal Bearings of Speed Increasing and Reduction Gearboxes Christophe Bouchoule, Michel Fillon, Daniel Nicolas, Franck Barresi 85 Bearings
TAMU Turbo Show 1995 Experience with Empirical Criteria for Rotating Stall in Radial Vaneless Diffusers John W. Fulton, William G. Blair 97 Centrifugal Compressors
TAMU Turbo Show 1995 Development and Field Application of a Single Rotor Design Dry Gas Seal Robert S. Evenson, Brian Mason, Alain G. St.Onge, Daniel V. Frederick 107 Compressor Seals
TAMU Turbo Show 1995 Cleaning Turbomachinery without Disassembly, Online and Offline Andrew P. Watson, Donald R. Carter, C. Dale Alleyne 117 Maintenance
TAMU Turbo Show 1995 Is the Dry Coupling Really Causing Your Vibration Problem Guill A. Cornejo, Joseph P. Corcoran, Sujen Chen 129 Coupling
TAMU Turbo Show 1995 Troubleshooting Bearing and Lube Oil System Problems Thomas H. McCloskey 147 Bearings; Corrosion; Lubrication Systems; Maintenance
TAMU Turbo Show 1995 Reciprocating Compressor Valve Reliability Improvements John R. Metcalf, Derek Woollatt 167 Reciprocating Compressors
TAMU Turbo Show 1995 Leakage and Rotordynamic Effects of Compressible Annular Seals Joseph K. Scharrer, Joseph M. Pelletti 175 Rotordynamics; Compressor Seals; Gas Turbines; Steam Turbines
TAMU Turbo Show 1995 User Insights for the Effective Purchase of New Turbomachinery Erwin A. Gaskamp, Robert E. Carpenter 191 Specifications
TAMU Turbo Show 1995 Improved Reliability Through the Use of Design Audits J. C. Wachel, Kenneth E. Atkins, James D. Tison 203 Design Audits
TAMU Turbo Show 1995 Dry Gas Seal Retrofit James F. Southcott, J. Michael Sweeney, Paul L. Feltman, Jr. 221 Centrifugal Compressors; Compressor Seals
TAMU Turbo Show 1996 Profiled Leading Edge Groove Tilting Pad Journal Bearing for Light Load Operation Stephen L. Edney, John K. Waite, Scan M. DeCamillo 1 Bearings, Critical Speed, Rotordynamics, Steam Turbines
TAMU Turbo Show 1996 Thrust Bearing Analysis, Optimization, and Case Histories John K. Whalen 17 Bearings
TAMU Turbo Show 1996 Selection, Design, and Field Testing of a 10,500 Horsepower Variable Speed Induction Motor Compressor Drive James H. Hudson 25 Centrifugal Compressors
TAMU Turbo Show 1996 Applying Variable Speed Drives with Static Frequency Converters to Turbomachinery Lucien Terens, Andrej Grgic 35 Electric motors; Fans; Pumps
TAMU Turbo Show 1996 Turbine Instability Solution—Honeycomb Seals Jay Armstrong, Frank Perricone 47 Rotordynamics; Steam Turbines
TAMU Turbo Show 1996 Squeeze Film Damper Bearing Experimental Vs Analytical Results for Various Damper Configurations Mark J. Kuzdzal, Jerry F. Hustak 57 Bearings; Critical Speed; Rotordynamics; Testing
TAMU Turbo Show 1996 Dynamic Data Analysis of Compressor Rotating Stall Frank Kushner 71 Axial Compressor; Centrifugal Compressors; Diagnostics; Testing
TAMU Turbo Show 1996 Surge Detection in an Industrial Axial Flow Compressor David H. Linden, Charles Parker 83 Axial Compressor; Operation; Testing; Vibration Monitoring
TAMU Turbo Show 1996 Full Power, Full Pressure, Closed-Loop Test of a Natural Gas Turboexpander Duane Bergmann, Hans Nijhuis 89 Rotordynamics; Testing; Turboexpanders
TAMU Turbo Show 1996 Application of High Speed and High Efficiency Hydrogen Turboexpanders in Refinery Service William A. Kardine, Reza R. Agahi, Behrooz Ershaghi, Fouad Y. Zeidan 95 Bearings; Turboexpanders
TAMU Turbo Show 1996 Rotating Equipment Loss Prevention—An Insurer's Viewpoint Edward E. Clark 103 Condition Monitoring; Couplings; Maintenance; Steam Turbines, Turboexpanders
TAMU Turbo Show 1996 Turbine Overhaul Frequency: Time or Performance Based? David A. Johns, John T. Bertucci 123 Inspection; Maintenance; Repair; Steam Turbines; Welding;
TAMU Turbo Show 1996 A Systematic Approach to Case Recertification Edward A. Abraham, Daniel E. Coleman, William S. Bielecki 133 Centrifugal Compressors; Inspection; Reapplication; Testing
TAMU Turbo Show 1996 Expander Field Remanent Life Analysis and Assessment David H. Linden 139 Condition Monitoring; Inspection; Materials; Turboexpanders
TAMU Turbo Show 1996 Design Improvements Enhance Dry Gas Seal's Ability to Handle Reverse Pressurization T. Paul Mayeux, Paul L. Feltman, Jr. 149 Centrifugal Compressors; Compressor Seals
TAMU Turbo Show 1996 A Mathematical Formalism for Flexural Diaphragm Fatigue Life and Reliability Evaluation Joseph A. Stocco, John E. Sisson, Robert H. Findlay 157 Alignment; Couplings; Specifications; Vibration Monitoring
TAMU Turbo Show 1996 The Design and Application of Squeeze Film Dampers in Rotating Machinery Fouad Y. Zeidan, Luis San Andres, John M. Vance 169 Bearings; Rotordynamics
TAMU Turbo Show 1996 Practical Design Against Torsional Vibration Mark A. Corbo, Stanley B. Melanoski 189 Critical Speed; Design Audits; Rotordynamics
TAMU Turbo Show 1996 Design Considerations for Thrust Bearing Applications James H. Ball 223 Bearings
TAMU Turbo Show 1996 Planning, Preparation, and Implementation of Turbomachinery Turnarounds Robert W. Parker, Douglas H. Collier, Donald A. Rudisel, Charles R. Rutan, Alan S. Pyle 243 Maintenance
TAMU Turbo Show 1996 Options for Low Speed and Operating Speed Balancing of Rotating Equipment Carroll Stroh, John R. MacKenzie, Jordan Rebstock 253 Balancing
TAMU Turbo Show 1997 Application Of Dry Gas Seals In Special Purpose Steam Turbines Theodore E. Bond, Mark Pospisil, E. V. Wilkinson 151 Noncontacting dry gas mechanical face seals, Steam Turbines
TAMU Turbo Show 1997 Expert Systems Provide Support For a Proactive Machinery Management Methodology Ronald F. Bosmans 195 Expert Systems, Knowledge Base, System Information
TAMU Turbo Show 1997 Stress Evaluation In High Speed Rotating Machinery With The LCR Ultrasonic Technique Don E. Bray, Martin Dietrich 143 Stress Evaluation, Ultrasonic Technique, Compressor Rotor, Coupling Pressure
TAMU Turbo Show 1997 Annular Gas Seals And Rotordynamics Of Compressors And Turbines Dara W. Childs, Leland T. Jordan, John M. Vance 201 Floating Ring Gas Seal, Honeycomb-Stator Seal, Labyrinth Seal
TAMU Turbo Show 1997 Steam Turbine Risk Assessment—A Tool to Assist in Optimizing Inspection and Overhauls of Industrial Steam Turbines Timothy J. Christ, Michael J. Drosjack, G. Mark Tanner 87 Quantitative Risk Analysis, Outage Planning Factors
TAMU Turbo Show 1997 Discovering, the Hard Way, How a High Performance Coupling Influenced the Critical Speeds and Bearing Loading of an Overhung Radial Compressor—A Case History Joseph P. Corcoran, Harvey Rea, Guill A. Cornejo, Martin L. Leonhard 67 Mechanical Test Procedures, Bearing Static Load Test, Coupling, Test Gearbox
TAMU Turbo Show 1997 Design and Retrofit of a Low Solidity Diffuser for a Pipeline Centrifugal Gas Compressor Application Michael B. Flathers 57 Production Compressors, Vaneless Diffusser, Solidity Diffusers, Field Retrofit
TAMU Turbo Show 1997 Installation Tools for Hydraulically Fitted Coupling Hubs—Precautions and Design Requirements C.B. Gibbons, A. Nigel Hearne 159 Design Alpha Tools, Design Beta Tools
TAMU Turbo Show 1997 Reliability Focused Maintenance System—A Case Study Bonz Hart, Paul Lane 189 RFMS Systems
TAMU Turbo Show 1997 Turbine Remanufacture—One Option for Reliability and Efficiency Improvement David A. Johns, David Rasmussen, James Beverly 95 Casing NDE, Bearing Housing Inspection, Valve Rack/Steam Chest Inspection
TAMU Turbo Show 1997 Flow-induced Turbocompressor and Piping Noise and Vibration Problems—Identification, Diagnosis, and Solution David E. Jungbauer, Linda L. Eckhardt 79 Acoustic Length Resonance, Vortex Shielding Excitation, Compressor System Design, Piping Modification
TAMU Turbo Show 1997 Field Testing of Gas Turbine Driven Centrifugal Compressor Packages—Test Procedures and Measurement Uncertainties Rainer Kurz, Klaus Brun 19 Centrifugal Compressors, Gas Composition Calculations
TAMU Turbo Show 1997 Rerate of Centrifugal Process Compressors—Wider Impellers or Higher Speed or Suction Side Boosting? Klaus Lüdtke 43 Wider Impellers, High Rotational Speeds, Two-Casing Air Compressor, Booster Compressor, Mass Flow
TAMU Turbo Show 1997 An Assessment of the Forces Acting upon a Centrifugal Impeller Using Full Load, Full Pressure Hydrocarbon Testing Cyril Borer, James Sorokes, Thomas McMahon, Edward Abraham 111 Aerodynamic Observations, CFD Results, Impeller Interaction
TAMU Turbo Show 1997 Understanding and Preventing Steam Turbine Overspeeds William E. Nelson, Perry C. Monroe, Jr. 129 Basic Trip/Throttle Valve Designs, Stop Valves, Steam Turbine Control Basic
TAMU Turbo Show 1997 Subtracting Residual Unbalance for Improved Test Stand Vibration Correlation John C. Nicholas, Stephen L. Edney, John A. Kocur, Jerry F. Hustak 7 Rotordynamic Predictions, Steam Turbines, Centrifugal Compressors, Residual Unbalance
TAMU Turbo Show 1997 High Speed Electric Drive Applications—An Overview John C. Rama, Miles Griggs 167 Equipment Design, Drive Systems, Maintenance Cost
TAMU Turbo Show 1997 Confirming Centrifugal Compressor Aerodynamic Performance Using Limited Test Data Combined with Computational Fluid Dynamic Techniques Shreekant Shah, John Bartos 35 Compressor Design, CFD Model and CFD Code, Centrifugal Compressor Design
TAMU Turbo Show 1997 Risk-based Maintenance of Turbomachinery Anthony J. Smalley, David A. Mauney 177 Cash Flow Maintenance, Risk Based Concepts
TAMU Turbo Show 1997 Vibration Reduction of Large Steam Turbine Generator Through Bearing Analysis/Modification Joseph W. Spencer, Jr., Don Osborne 1 Analytical Modeling, Exciter Rotor, Bearing Characteristics
TAMU Turbo Show 1997 Cost Effective Re-engineering of a Propylene Compressor String John F. Vanderhoff, John R. Dugas, Jr. 123 Aerodynamic Modelling, Design Drafting of Required Parts, Manufacturing and Assembly Process, Rerate Philosophy
TAMU Turbo Show 1998 Experience with High Speed Induction Motors for Direct Driving of Compressors Dominique C. Gilon, Louis Boutriau 1 Electric Motors
TAMU Turbo Show 1998 Starter Motor Sizing for Large Gas Turbine (Single-Shaft) Driven LNG Strings Bruce G. Heckel, Frank W. Davis 7 Centrifugal Compressors; Electric Motors; Testing; Gas Turbines
TAMU Turbo Show 1998 Application of a Heat Barrier Sleeve to Prevent Synchronous Rotor Instability Frits M. de Jongh, Pieter van der Hoeven 17 Bearings; Centrifugal Compressors; Rotordynamics; Testing
TAMU Turbo Show 1998 Synchronous Motor Lateral Vibration Dynamics—Diagnosis, Resolution, and Field Implementation B. Fred Evans, Larry G. Shabi 27 Bearings; Critical Speed; Motors; Rotordynamics
TAMU Turbo Show 1998 Advanced Dry Gas Seal by the Dynamic Ion Beam Mixing Technique Takao Takeuchi, Tadashi Kataoka, Hiroshi Nagasaka, Momoko Kakutani, Masanobu Ito, Ryoji Muraki 39 Centrifugal Compressors; Materials; Metallurgy; Compressor Seals; Testing;
TAMU Turbo Show 1998 Development of a Sulfidation-Corrosion Resistant Ni-base Superalloy for FCC Power Recovery Turbine Rotors Hiroshi Yakuwa, Toshio Narita, Masamichi Kawasaki, Matsuho Miyasaka, Cheng Fang, Tetsu Go, Shuhei Nakahama 49 Corrosion; Energy; Materials; Metallurgy; Turboexpanders;
TAMU Turbo Show 1998 Root Cause Analysis of a Long Term Reliability Problem with Reciprocating Compressors in H2 Service Michael J. Drosjack, Philip E. O’Neill, Dale V. Lorio 55 Reciprocating Compressors
TAMU Turbo Show 1998 Design Modifications and Active Balancing on an Integrally Forged Steam Turbine Rotor to Solve Serious Reliability Problems Darayus Pardivala, Stephen W. Dyer, Clark D. Bailey 67 Balancing; Controls; Rotordynamics; Steam Turbines
TAMU Turbo Show 1998 High Speed Oil-Free Turbomachinery String Ali Al Safwani, Pranabesh DeChoudhury, Martin Garvey, Chet Farabaugh 77 Bearings; Centrifugal Compressors; Rotordynamics; Steam Turbines
TAMU Turbo Show 1998 Vibration and Eccentricity Measurements Combined with Rotordynamic Analyses on a Six Bearing Turbine Generator David R. Gruwell, Fouad Y. Zeidan 85 Rotordynamics
TAMU Turbo Show 1998 Eliminating Oil Leaks by Optimizing Bearing Case Oil Labyrinths John K. Whalen, Skip Krieser 93 Bearings; Centrifugal Compressors; Lubrication Systems; Compressor Seals; Steam Turbines;
TAMU Turbo Show 1998 Increased Reliability and Reduction in Long Term Cost of Ownership Through Proper Spare Rotor Storage, Inspection, Documentation, and Tracking Rod Mitchell 101 Corrosion; Inspection; Maintenance; Preservation; Repair;
TAMU Turbo Show 1998 Acoustic Fatigue Involving Large Turbocompressors and Pressure Reduction Systems David E. Jungbauer, Larry E. Blodgett 111 Diagnostics; Noise; Piping; Testing; Vibration Monitoring;
TAMU Turbo Show 1998 Redesign of the Last Two Stages of a Mechanical Drive Steam Turbine David A. Henry, Paul E. DiCristoforo, Timothy J. Ewer, Michael Mindock 119 Steam Turbines; Welding
TAMU Turbo Show 1998 Gas Turbine Blade Failures—Causes, Avoidance, and Troubleshooting Cyrus B. Meher-Homji, George A. Gabriles 129 Axial Compressors: Condition Monitoring: Design Audits; Gas Turbines
TAMU Turbo Show 1998 Magnetic Bearings—A Primer Paul Alves 181 Bearings; Diagnostics; Maintenance; Operation; Specifications;
TAMU Turbo Show 1998 Materials Issues for Users of Gas Turbines Henry L. Bernstein 197 Materials; Gas Turbines
TAMU Turbo Show 1998 Guidelines for Specifying and Evaluating New and Rerated Multistage Centrifugal Compressors James F. Blahovec, Terryl Matthews, Kevin S. Eads 215 Centrifugal Compressors; Couplings; Reapplication; Rotordynamics; Specifications.;
TAMU Turbo Show 1999 Advances in Erosion Prediction of Axial Flow Expanders Ben Carbonetto, Greg Hoch 1 Design Audits; Gas Turbines; Turboexpancers
TAMU Turbo Show 1999 Analysis of Hot Section Failures on Gas Turbines in Process Plant Service Ian Hunter, Joe Daleo, James Wilson, Keith Ellison 9 Maintenance; Metallurgy; Operation; Gas Turbines
TAMU Turbo Show 1999 Use of Metal Bellow Noncontacting Seals and Guidelines for Steam Applications Lionel Young, Joel N. Burroughs, Michael Huebner 21 Maintenance; Compressor Seals; Pump Seals; Steam Turbines
TAMU Turbo Show 1999 Retrofitting a Large Steam Turbine with a Mechanically Centered Squeeze Film Damper Stephen L. Edney, John C. Nicholas 29 Critical Speed; Rotordynamics; Steam Turbines
TAMU Turbo Show 1999 Unexpected Rotordynamic Instability in a "Proven" FCC Wet Gas Compressor Ed Wilcox 41 Bearings; Centrifugal Compressors; Rotordynamics; Compressor Seals
TAMU Turbo Show 1999 Improvement of Centrifugal Compressor Reliability Handling High Pressure and High Density Gas Richard S. Gill, Hiroaki Osaki, Yasushi Mouri, Yasuhiro Kawashima 51 Bearings; Centrifugal Compressors; Rotordynamics; Compressor Seals
TAMU Turbo Show 1999 Methodology of Open Bladed Impeller Resonance Identification Qian Wang, John C. Bartos, Russell A. Houston 61 Centrifugal Compressors
TAMU Turbo Show 1999 Use of Computational Fluid Dynamics and Scale Model Component Testing for a Large FCC Prototype Air Compressor, The Michael Kotlyar, Reid Engstrom, Marco Giachi 69 Centrifugal Compressors; Operation; Testing
TAMU Turbo Show 1999 Solutions to Field Problems of a Gas Turbine-Axial Flow Chemical Process Train Based on Computer Simulation of the Process Francisco Gonzalez, Meherwan P. Boyce 77 Axial Compressors; Gas Turbines
TAMU Turbo Show 1999 Gas Turbine Power Augmentation by Fogging of Inlet Air Cyrus B. Meher-Homji, Thomas R. Mee III 93 Gas Turbines
TAMU Turbo Show 1999 Rotordynamic Stability Tests on High-Pressure Radial Compressors Urs Baumann 115 Centrifugal Compressors; Rotordynamics; Compressor Seals; Testing
TAMU Turbo Show 1999 Redesign of Large Steam Turbines for Increased Reliability Malcolm E. Leader, Randal G. Rials, Charles R. Rutan 123 Steam Turbines
TAMU Turbo Show 1999 Influence of Oil Injection Method on Thrust Bearing Performance at Low Flow Conditions Christopher B. Stewart 133 Operation; Testing
TAMU Turbo Show 1999 High Frequency Fatigue Failure in Silencer/Pulsation Dampers for Oil Free Screw Compressors Jeff Lovelady, Peter A. Bielskus 141 Screw Compressors; Design Audits; Noise; Piping
TAMU Turbo Show 1999 Basics of Operation and Application of Oil Flooded Rotary Screw Compressors Joseph W. Pillis 147 Screw Compressors; Lubrication Systems
TAMU Turbo Show 1999 Steam Turbine Governing Systems and Electronic Governor Retrofit Joseph S. Lamberson, Jack Reed 157 Steam Turbines
TAMU Turbo Show 1999 Practical Methods for Field Performance Testing Centrifugal Compressors Ed Wilcox 165 Centrifugal Compressors; Testing
TAMU Turbo Show 1999 High Temperature Coatings for Industrial Gas Turbine Users Henry L. Bernstein 179 Gas Turbines
TAMU Turbo Show 1999 Sources and Remedies of High-Frequency Piping Vibration and Noise Stephen M. Price, Donald R. Smith 189 Centrifugal Compressors; Screw Compressors; Noise; Piping Testing
TAMU Turbo Show 1999 Field Performance Testing of Gas Turbine Driven Compressor Sets Rainer Kurz, Klaus Brun, Daryl D. Legrand 213 Centrifugal Compressors; Testing; Gas Turbines
TAMU Turbo Show 2000 Debottlenecking Hydrogen Reciprocating Compressors and Synchronous Motors Shailendra K. Gupta, Chris L. McCormick, Charles W. Melcher, Jeffrey L. Schalk 1 Reciprocating Compressors; Design Audits; Electric Motors
TAMU Turbo Show 2000 Rod Drop Monitoring, Does It Really Work? Steven M. Schultheis, Brian F. Howard 11 Reciprocating Compressors; Condition Monitoring; Diagnostics; Testing; Vibration Monitoring
TAMU Turbo Show 2000 Sidestream Optimization Through the Use of Computational Fluid Dynamics and Model Testing James M. Sorokes, David A. Nye, Nicholas D’Orsi, Rob Broberg 21 Centrifugal Compressors; Testing
TAMU Turbo Show 2000 Upgrading Centrifugal Compressors with Polymer Seals in an Ethylene Plant—A Case History John K. Whalen, John R. Dugas, Jr. 31 Centrifugal Compressors; Materials; Compressor Seals
TAMU Turbo Show 2000 Design, Testing, and Field Experience of a High-Pressure Natural Gas Reinjection Compressor Norbert G. Wagner, Frits M. de Jongh, Robert Moffat 39 Centrifugal Compressors; Operation; Rotordynamics; Compressor Seals; Testing
TAMU Turbo Show 2000 Gas Damper Seal Test Results, Theoretical Correlation, and Applications in Design of High-Pressure Compressors Jiming Li, Frank Kushner, Pranabesh DeChoudhury 55 Centrifugal Compressors; Rotordynamics; Compressor Seals; Testing
TAMU Turbo Show 2000 Design and Experience with a 30,000 HP Magnetic Bearing Supported Motor Driven Turbocompressor for a Speed Range of 600 to 6300 RPM Horst Kümmlee, Wim H. de Groot, Gerrit M. Lenderink, Richard R. Shultz 65 Bearings; Centrifugal Compressors; Electric Motors; Motors; Rotordynamics;
TAMU Turbo Show 2000 Design Considerations for a 66,000 HP Motor Driving an Air Compressor Mark DeBlock 81 Critical Speed; Foundations; Materials; Motors; Rotordynamics;
TAMU Turbo Show 2000 Multiple Resonance Vibration Mitigation on a 54,000 HP Parallel Shaft Double Helical Speed Increaser B. Fred Evans, James F. McCraw, Greg Elliott 93 Bearings; Critical Speed; Gears; Rotordynamics
TAMU Turbo Show 2000 Critical Review of Compressor Impeller Vibration Parameters for Failure Prevention Frank Kushner, Shawn J. Richard, Robert A. Strickland 103 Centrifugal Compressors; Diagnostics; Fans; Operation
TAMU Turbo Show 2000 Influence of Previous Operational Cycle on the Microstructure of Rejuvenated Ni-Base Superalloy Gas Turbine Blades after Their Return to Service Evgenia Lvov, Donald Norsworthy 113 Materials; Metallurgy; Repair; Testing; Gas Turbines;
TAMU Turbo Show 2000 Low Emission Combustion Technology for Stationary Gas Turbine Engines Stuart A. Greenwood 125 Gas Turbines
TAMU Turbo Show 2000 Recent Technologies for the Reliability and Performance of Mechanical-Drive Steam Turbines in Ethylene Plants Tomoyoski Sasaki, Satoshi Hata, Masahiro Kobayashi, Osamu Isumi 135 Energy; Materials; Testing; Steam Turbines; Welding;
TAMU Turbo Show 2000 FCC Hot Gas Expander Reliability Upgrade Evaluation Shailendra K. Gupta, David L. Boomer, Lynn C. Fulton 145 Axial Compressors; Condition Monitoring; Design Audits; Energy; Operation
TAMU Turbo Show 2000 Torsional Vibration Analysis of Synchronous Motor-Driven Turbomachinery Mark A. Corbo, Clifford P. Cook 161 Centrifugal Compressors; Critical Speed; Design Audits; Electric Motors; Rotordynamics
TAMU Turbo Show 2000 Evaluation of a High Speed, Light Load Phenomenon in Tilting-Pad Thrust Bearings Joseph J. Wilkes, Scan M. DeCamillo, Mark J. Kuzdzal, James D. Mordell 177 Bearings; Centrifugal Compressors; Testing
TAMU Turbo Show 2000 Review of API Versus AGMA Gear Standards/Rating, Data Sheet Completion, and Gear Selection Guidelines Ken Beckman, Vinod P. Patel 191 Gears, Specifications
TAMU Turbo Show 2000 Designing High Performance Steam Turbines with Rotordynamics as a Prime Consideration Stephen L. Edney, George M. Lucas 205 Critical Speed; Rotordynamics; Testing; Steam Turbines
TAMU Turbo Show 2000 API Centrifugal Compressor Oil Seals and Support Systems-Types, Selection, and Field Troubleshooting Ed Wilcox 225 Centrifugal Compressors; Lubrication Systems; Compressor Seals
TAMU Turbo Show 2000 Integrally Geared API 617 Process Gas Compressors Peter J. Beaty, Klaus Eisele, Thomas D. Maceyka, Carl Schwarz 239 Centrifugal Compressors; Gears; Specifications
TAMU Turbo Show 2000 Gas Turbine Performance—What Makes the Map? Rainer Kurz, Klaus Brun 247 Axial Compressors; Energy; Testing; Gas Turbines
TAMU Turbo Show 2000 A Review of Aerodynamically Induced Forces Acting on Centrifugal Compressors, and Resulting Vibration Characteristics of Rotors D. Fred Marshall, James M. Sorokes 263 Centrifugal Compressors; Vibrations; Rotordynamics; Testing
TAMU Turbo Show 2000 The Historical Evolution of Turbomachinery Cyrus B. Meher-Homji 281 Axial Compressors; Centrifugal Compressors; Gas Turbines; Steam Turbines
TAMU Turbo Show 2001 Two Unusual and Catastrophic Bearing Failures Caused by Electrical Arcing in the Oil Film, Their Causes, and the Surprisingly Simple Solutions That Cured Them Jigger Jumonville, Erik Rasmussen 1
TAMU Turbo Show 2001 A Study of Parameters that Affect Pivoted Shoe Journal Bearing Performance in High-Speed Turbomachinery Scan M. DeCamillo, Keith Brockwell 9
TAMU Turbo Show 2001 Innovative Gas Turbine Performance Diagnostics and Hot Parts Life Assessment Techniques Erio Benvenuti 23
TAMU Turbo Show 2001 Improved Steam Turbine Leakage Control with a Brush Seal Design Ryan M. Pastrana, Christopher E. Wolfe, Norman A. Turnquist, Mark E. Burnett 33
TAMU Turbo Show 2001 Rotor Instability Problems in an Integrally Geared Compressor Supported by Tilting Pad Bearings Peter M. Gruntfest, Leo Andronis, William D. Marscher 39
TAMU Turbo Show 2001 Electric Power Supply Instabilities Exciting Torsional and Lateral Vibrations of an Integrally Geared Turbocompressor Martin L. Leonhard, Ulrich Kern, Klaus Reischl 49
TAMU Turbo Show 2001 Efficiency Improvements on Large Mechanical Drive Steam Turbines Nathan T. Little, Erik M. Sulda, Terry N. Terezakis 57
TAMU Turbo Show 2001 Eliminating a Rub-Induced Startup Vibration Problem in an Ethylene Drive Steam Turbine John C. Nicholas, Stephen L. Edney, Terryl Matthews, Francisco J. Mourente Varela 65
TAMU Turbo Show 2001 Full-Load Testing of an All-Electric Centrifugal Compressor for Miscible Gas Injection John W. Fulton, John M. Klein, Andrew Marriott, A. David Graham 79
TAMU Turbo Show 2001 Centrifugal Compressor Noise Reduction by Using Helmholtz Resonator Arrays Zheji Liu, D. Lee Hill 89
TAMU Turbo Show 2001 Maintenance and Online Diagnostics on Gearboxes in the Petrochemical Industry Michel Wendling, Edwin Becker 95
TAMU Turbo Show 2001 Application of Foil Bearings to Helium Turbocompressor H. Ming Chen, Roy Howarth, Bernard Geren, Jay C. Theilacker, William M. Soyars 103
TAMU Turbo Show 2001 Corrosion Control in Industrial Axial Flow Compressors David H. Linden 115
TAMU Turbo Show 2001 Coupling Interface Connection Jon R. Mancuso, Roger L. Jones 121
TAMU Turbo Show 2001 Gas Turbine Performance Deterioration Cyrus B. Meher-Homji, Mustapha A. Chaker, Hatim M. Motiwala 139
TAMU Turbo Show 2001 Elements of Mechanical Equipment Life-Cycle Cost Analysis Jim E. Bryant, Ernest F. Pead, Stan Polonski, Jim Sabrsula, Joe V. Spiller 176
TAMU Turbo Show 2001 The New Fifth Edition of API 618 for Reciprocating CompressorsCWhich Pulsation and Vibration Control Philosophy Should You Use? James D. Tison, Kenneth E. Atkins 183
TAMU Turbo Show 2001 Do What I Say (The Effect of the Process on Turbomachinery Reliability) William E. Forsthoffer 197
TAMU Turbo Show 2001 Design, Operation, and Maintenance Considerations for Improved Dry Gas Seal Reliability in Centrifugal Compressors John S. Stahley 203
TAMU Turbo Show 2001 Online, Continuous Monitoring of Mechanical Condition and Performance for Critical Reciprocating Compressors William A. Griffith, Edward B. Flanagan 209
TAMU Turbo Show 2001 Proven Methods for Evaluating the Health Condition of Piston Compressors Alex Deitermann, David Jetelina 219
TAMU Turbo Show 2002 Subsea Centrifugal Compressor Development--Breakthrough Technology for Oil and Gas Offshore Production Sabrina Tasselli, Stefano Terzi, Leonardo Baldassarre, Andrea Masi, Riccardo Beccaluva, Daniela Ghirelli 1
TAMU Turbo Show 2002 New Designs and Applications for Increased Power Recovery and Improved Reliability in FCC Expanders Ben Carbonetto, Greg Hoch 9
TAMU Turbo Show 2002 Practical Use of Rotordynamic Analysis and Troubleshooting Skills to Correct a Long-Term Synchronous Vibration Problem in an Overhung Turboblower Mark A. Corbo, Thomas J. Kuli, H. Leslie Gutzwiller 17
TAMU Turbo Show 2002 Rotordynamic Stability Measurement During Full-Load, Full-Pressure Testing of a 6000 PSI Reinjection Centrifugal Compressor J. Jeffrey Moore, Stephen T. Walker, Mark J. Kuzdzal 29
TAMU Turbo Show 2002 Rotordynamic Tests of a Flexible Rotor on Flexure Pivot Journal Bearings and Stability Correlation with Frequency Dependent Characteristics Brian C. Pettinato, Pranabesh De Choudhury 39
TAMU Turbo Show 2002 Compressor Discharge Pipe Failure Investigation with a Review of Surge, Rotating Stall, and Piping Resonance Frank Kushner, Doug Walker, William C. Hohlweg 49
TAMU Turbo Show 2002 Current and Vibration Monitoring for Fault Diagnosis and Root Cause Analysis of Induction Motor Drives William T. Thomson, Philip Orpin 61
TAMU Turbo Show 2002 Assessment of Technology and Economic Benefits of Reciprocating Machine Condition Monitoring and Diagnostic Systems Robert Gaechter 69
TAMU Turbo Show 2002 New Technologies of Synthesis Gas Compressor Drive Steam Turbines for Increasing Efficiency and Reliability Tomoyoshi Sasaki, Satoshi Hata, Kyoichi Ikeno 75
TAMU Turbo Show 2002 Compressor Seals for Hydrogen Recycle Service Stephen L. Ross, M. Theodore Gresh, Robert M. Kranz 85
TAMU Turbo Show 2002 Troubleshooting Turbomachinery Using Startup and Coastdown Vibration Data Ed Wilcox 91
TAMU Turbo Show 2002 Troubleshooting Turbine Steam Path Damage Mechanisms Thomas McCloskey 105
TAMU Turbo Show 2002 Dry Gas Seal System Design Standards for Centrifugal Compressor Applications John S. Stahley 145
TAMU Turbo Show 2002 Torsional Vibration Analysis and Testing of Synchronous Motor-Driven Turbomachinery Mark A. Corbo, Clifford P. Cook, Charles W. Yeiser, Michael J. Costello 153
TAMU Turbo Show 2002 Engineering Fundamentals of Multi-MW Variable Frequency Drives--How They Work, Basic Types, and Application Considerations William J. Weber, Robert M. Cuzner, Eric J. Ruckstadter, Jim Smith 177
TAMU Turbo Show 2003 Solving Stability Problems While Commissioning a 100 MW Turbine Generator Set John K. Whalen, Malcolm E. Leader 1 Bearings; Cogeneration; Critical Speed; Rotordynamics; Steam Turbines
TAMU Turbo Show 2003 Determining the Root Causes of Subsynchronous Instability Problems in Two Centrifugal Compressors Ed Wilcox, Dave P. O'Brien 9 Bearings; Centrifugal Compressors; Critical Speed; Rotordynamics; Vibration Monitoring
TAMU Turbo Show 2003 Age Related Failures in Magnetic Bearing Systems Jigger Jumonville, Kevin Yates 21 Bearings; Condition Monitoring; Maintenance; Turboexpanders; Vibration Monitoring
TAMU Turbo Show 2003 Tilting Pad Journal Bearings with Spray-Bar Blockers and Bypass Cooling for High Speed, High Load Applications John C. Nicholas 27 Bearings; Centrifugal Compressors; Gears
TAMU Turbo Show 2003 Instability of a High Pressure Compressor Equipped with Honeycomb Seals Massimo Camatti, Giuseppe Vannini, John Fulton, Fred Hopenwasser 39 Centrifugal Compressors; Rotordynamics; Compressor Seals; Testing
TAMU Turbo Show 2003 Evaluation of Centrifugal Compressor Stability Margin and Investigation of Anti-Swirl Mechanism Jiming Li, Pranabesh De Choudhury, Frank Kushner 49 Centrifugal Compressors; Design Audits; Rotordynamics; Compressor Seals; Testing
TAMU Turbo Show 2003 Resonance Identification for Impellers Murari P. Singh, Bhabesh K. Thakur, William E. Sullivan, George Donald 59 Centrifugal Compressors; Vibration Monitoring
TAMU Turbo Show 2003 Desktop Use of Computational Fluid Dynamics to Design and Troubleshoot Compressors and Turboexpanders Grant Nordwall, Jigger Jumonville, Terryl Matthews 71 Bearings; Centrifugal Compressors; Diagnostics; Testing; Turboexpanders
TAMU Turbo Show 2003 Improved Bearing AlloyCA Contribution Toward Environmental Protection Rolf Koring 85 Bearings; Gears; Metallurgy; Gas Turbines; Steam Turbines
TAMU Turbo Show 2003 Development of Anti-Fouling and Corrosion Resistant Coatings for Petrochemical Compressors Wenchao Wang, Phillip Dowson, Amir Baha 91 Axial Compressors; Centrifugal Compressors; Corrosion; Materials
TAMU Turbo Show 2003 Elimination of Flow-Induced Instability from Steam Turbine Control Valves Jim Hardin, Frank Kushner, Stephen Koester 99 Governors; Noise; Repair; Steam Turbines
TAMU Turbo Show 2003 Turbine Overspeed Trip Protection Charles R. Rutan 109 Failure Analysis
TAMU Turbo Show 2003 Synchronous Thermal Instability Prediction for Overhung Rotors R. Gordon Kirk, Zenglin Guo, Avinash C. Balbahadur 121 Bearings; Centrifugal Compressors; Design Audits; Rotordynamics; Turboexpanders
TAMU Turbo Show 2003 Recycle Gas Compressor Designed for High Unbalance Tolerance and Stability Stephen R. Locke, Wolfgang Faller 137 Bearings; Centrifugal Compressors; Maintenance; Operation; Rotordynamics
TAMU Turbo Show 2003 Motor Current Signature Analysis to Detect Faults in Induction Motor DrivesCFundamentals, Data Interpretation, and Industrial Case Histories William T. Thomson, Ronald J. Gilmore 145 Compressors; Condition Monitoring; Diagnostics; Electric Motors; Maintenance
TAMU Turbo Show 2003 Mechanical Upgrades to Improve Centrifugal Compressor Operation and Reliability John S. Stahley 157 Centrifugal Compressors; Maintenance; Noise; Operation; Compressor Seals
TAMU Turbo Show 2003 Compressor Seal Selection and Justification Stephen L. Ross, Raymond F. Beckinger 167 Centrifugal Compressors; Compressor Seals
TAMU Turbo Show 2003 Online Techniques to Mitigate the Risks That Limit Expander Reliability Ben Carbonetto 179 Design Audits; Materials; Gas Turbines; Turboexpanders
TAMU Turbo Show 2003 What Are the Differences in High Performance Flexible Couplings for Turbomachinery? Jon R. Mancuso, Joe Corcoran 189
TAMU Turbo Show 2003 The Use of Integrally Geared Compressors Based on Two Industrial Gas Companies= Experience Joseph G. Wehrman, Thomas E. Walder, Nicholas J. Haryett 209 Centrifugal Compressors
TAMU Turbo Show 2004 RESOLVING A RESONANT FATIGUE PROBLEM ON A LARGE RADIAL INFLOW EXPANDER Glenn R. Doerksen, J. Charles Berggren 1 Lecture
TAMU Turbo Show 2004 PROBABILISTIC LIFE ASSESSMENT OF AN IMPELLER WITH DISCONTINUITIES 15 Lecture
TAMU Turbo Show 2004 LOW FREQUENCY INSTABILITY IN A PROCESS COMPRESSOR John A. Kocur, Jr., George C. Hayles, Jr. 25 Lecture
TAMU Turbo Show 2004 CHANGING AND CONTROLLING THE “FIRST CRITICAL SPEED” OF OVERHUNG, CENTRIFUGAL FANS S. Ted Myrick, Jr., W. Barry Crawford, Gerald Schumpert 33 Lecture
TAMU Turbo Show 2004 COOLING AND LUBRICATION OF HIGH-SPEED HELICAL GEARS Patrick J. Smith 41 Lecture
TAMU Turbo Show 2004 HIGH PRESSURE OIL-INJECTED SCREW GAS COMPRESSORS (API 619 DESIGN) FOR HEAVY DUTY PROCESS GAS APPLICATIONS Takao Ohama, Takao Koga, Yoshinori Kurioka 49 Lecture
TAMU Turbo Show 2004 NEW TECHNOLOGY FOR ONLINE WASHING OF LARGE MECHANICAL-DRIVE CONDENSING STEAM TURBINES Gampa Bhat, Satoshi Hata, Kyoichi Ikeno, Yuzo Tsurusaki 57 Lecture
TAMU Turbo Show 2004 ON FUEL SUITABILITY FOR GAS TURBINES Rainer Kurz, Colin Etheridge, Roland Kaiser 67 Lecture
TAMU Turbo Show 2004 LIFE CYCLE COST ASSESSMENT OF TURBOMACHINERY FOR OFFSHORE APPLICATIONS Marcelo Accorsi Miranda, Eduardo Siqueira Brick 77 Lecture
TAMU Turbo Show 2004 TRANSFERRING CUSTODY OF IN-SERVICE TURBOMACHINERY—WHAT SELLERS AND BUYERS SHOULD CONSIDER S. T. Ganesan 85 Lecture
TAMU Turbo Show 2004 DEVELOPMENT OF ABRADABLE AND RUB TOLERANT SEAL MATERIALS FOR APPLICATION IN CENTRIFUGAL COMPRESSOR AND STEAM TURBINES Phillip Dowson, Michael Walker, Andrew Watson 95 Lecture
TAMU Turbo Show 2004 APPLICATION AND OPERATING HISTORY OF MODERATE-SPEED API 618 RECIPROCATING COMPRESSORS George M. Kopscick 103 Lecture
TAMU Turbo Show 2004 THERMOPLASTIC LABYRINTH SEALS FOR CENTRIFUGAL COMPRESSORS John K. Whalen, Eduardo Alvarez, Lester Palliser 113 Tutorial
TAMU Turbo Show 2004 TUTORIAL ON CRYOGENIC TURBOEXPANDERS Jigger Jumonville 127 Tutorial
TAMU Turbo Show 2004 API 613 FIFTH EDITION, SPECIAL PURPOSE GEAR UNITS FOR PETROLEUM, CHEMICAL, AND GAS INDUSTRY SERVICES—OVERVIEW PRESENTATION Robert W. Conner, Kenneth O. Beckman 135 Tutorial
TAMU Turbo Show 2004 ROTATING COMPONENT MODAL ANALYSIS AND RESONANCE AVOIDANCE RECOMMENDATIONS Frank Kushner 143 Tutorial
TAMU Turbo Show 2004 GAS TURBINE AXIAL COMPRESSOR FOULING AND WASHING Cyrus B. Meher-Homji, Andrew Bromley 163 Tutorial
TAMU Turbo Show 2004 BALANCE THIS! CASE HISTORIES FROM DIFFICULT BALANCE JOBS Troy D. Feese, Phillip E. Grazier 193 Tutorial
TAMU Turbo Show 2005 TURBINE FAILURE AND RECONSTRUCTION Charles R. Rutan 1 Lecture
TAMU Turbo Show 2005 REPAIR TECHNOLOGIES OF MECHANICAL DRIVE STEAM TURBINES FOR CATASTROPHIC DAMAGE Manabu Saga, Shugo Iwasaki, Yuzo Tsurusaki, Satoshi Hata 15 Lecture
TAMU Turbo Show 2005 ROTORDYNAMIC DESIGN OF CENTRIFUGAL COMPRESSORS IN ACCORDANCE WITH THE NEW API STABILITY SPECIFICATIONS John C. Nicholas, John A. Kocur 25 Lecture
TAMU Turbo Show 2005 EXPERIENCES AND APPLICATIONS OF API 617 FULLSTABILITYANALYSIS (LEVELII) ON CENTRIFUGALCOMPRESSORS Jiming Li, Pranabesh De Choudhury, Mike Sharples, John Wright 35 Lecture
TAMU Turbo Show 2005 GAS TURBINE LIFE LIMITING EFFECTS OF INLET AND INTERSTAGE WATER INJECTION Klaus Brun, Rainer Kurz 45 Lecture
TAMU Turbo Show 2005 SITE PERFORMANCE TEST EVALUATION FOR GAS TURBINE AND ELECTRIC MOTOR DRIVEN COMPRESSORS Rainer Kurz, Klaus Brun 53 Lecture
TAMU Turbo Show 2005 HERMETICALLY SEALED OIL-FREE TURBOCOMPRESSOR TECHNOLOGY George Kleynhans, Gary Pfrehm, Heinz Berger, Luc Baudelocque 63 Lecture
TAMU Turbo Show 2005 REMAINING LIFE ASSESSMENT OF STEAM TURBINE AND HOT GAS EXPANDER COMPONENTS Phillip Dowson, Wenchao Wang, Agustin Alija 77 Lecture
TAMU Turbo Show 2005 AXIAL ALIGNMENT AND THERMAL GROWTH EFFECTS ON TURBOMACHINERY TRAINS WITH DOUBLE-HELICAL GEARING Thom Eldridge, Greg Elliot, Ed Martin, M. Shukri Hitam 93 Lecture
TAMU Turbo Show 2005 APPLICATION OF A CRACK-CLOSURE MODEL FOR TURBINE LIFE ASSESSMENT Neville F. Rieger, Ronald N. Salzman 105 Lecture
TAMU Turbo Show 2005 PERFORMANCE EVALUATION OF A CENTRIFUGAL COMPRESSOR OPERATING UNDER WETGAS CONDITIONS Lars Brenne, Tor Bjørge, José L. Gilarranz, Jay M. Koch, Harry F. Miller 111 Lecture
TAMU Turbo Show 2005 EQUATION OF STATE INFLUENCES ON COMPRESSOR PERFORMANCE DETERMINATION Mark R. Sandberg 121 Lecture
TAMU Turbo Show 2005 GAS TURBINE PERFORMANCE Rainer Kurz 131 Tutorial
TAMU Turbo Show 2005 HYDRAULIC SHOP PERFORMANCE TESTING OF CENTRIFUGAL COMPRESSORS Gary M. Colby 147 Tutorial
TAMU Turbo Show 2005 FUNDAMENTALS OF FLUID FILM JOURNAL BEARING OPERATION AND MODELING Minhui He, C. Hunter Cloud, James M. Byrne 155 Tutorial
TAMU Turbo Show 2005 ASSESSING USEFUL LIFE OF TURBOMACHINERY COMPONENTS Murari P. Singh, Bhabesh K. Thakur, William E. Sullivan 177 Tutorial
TAMU Turbo Show 2005 APPLIED RISK AND RELIABILITY FOR TURBOMACHINERY PARTI—RELIABILITY PROCESSES Charles R. Rutan 193 Tutorial
TAMU Turbo Show 2005 APPLIED RISK AND RELIABILITY FOR TURBOMACHINERY PARTII—RELIABILITY CALCULATIONS Shiraz Pradhan 198 Tutorial
TAMU Turbo Show 2006 COMMUNICATION AND ACCOUNTABILITY ARE THE KEYS TO SUCCESS IN CONDITION-BASED MAINTENANCE Mark Mitchell, Steve Quillen, E. Forrest Pardue, Dick Hancock 1 LECTURES
TAMU Turbo Show 2006 WHAT TO DO WHEN A “CLASSIC” RCA DOESN’T GIVE THE ANSWER—APPLY DETAILED ENGINEERING ANALYSIS Michael J. Drosjack, John W. Felten, George H. Seamon,Timothy R. Griffin 7 LECTURES
TAMU Turbo Show 2006 DESIGN, MANUFACTURE, AND TESTING OF A HIGH SPEED 10 MW PERMANENT MAGNET MOTOR AND DISCUSSION OF POTENTIAL APPLICATIONS James S. Smith, Andrew P. Watson 19 LECTURES
TAMU Turbo Show 2006 ADVANCED CONTROL TECHNIQUE OF CENTRIFUGAL COMPRESSOR FOR COMPLEX GAS COMPRESSION PROCESSES Kazuhiro Takeda, Kengo Hirano 25 LECTURES
TAMU Turbo Show 2006 REVAMPING A GAS COMPRESSOR DRIVE TRAIN FROM 7000 TO 8000 HP WITH A NEW SYNCHRONOUS MOTOR DRIVER AND A CONTROLLED SLIP CLUTCH MECHANISM Charles W. Yeiser, Volker Hütten, Akram Ayoub, Robert Rheinboldt 33 LECTURES
TAMU Turbo Show 2006 AN IMPELLER DYNAMIC RISK ASSESSMENT TOOLKIT Donald M. Schiffer, Asadullah Syed 49 LECTURES
TAMU Turbo Show 2006 THE ROLEOFONLINE AERODYNAMIC PERFORMANCE ANALYSIS Robert L. DeMaria, M. Theodore Gresh 55 LECTURES
TAMU Turbo Show 2006 THE CONSEQUENCES OF COMPRESSOR OPERATION IN OVERLOAD James M. Sorokes, Harry F. Miller, Jay M. Koch 63 LECTURES
TAMU Turbo Show 2006 EFFECTS OF A WATER-MIST FIRE PROTECTION SYSTEM ON INTEGRITY AND OPERATION OF A HEAVY-DUTY GAS TURBINE Lorenzo Naldi, Michele D’Ercole 73 LECTURES
TAMU Turbo Show 2006 FULL LOAD, FULL SPEED TEST OF TURBOEXPANDER-COMPRESSOR WITH ACTIVE MAGNETIC BEARINGS Frank Davis, Reza Agahi, Randy Wu 81 LECTURES
TAMU Turbo Show 2006 PROCESS GAS APPLICATIONS WHERE API 619 SCREW COMPRESSORS REPLACED RECIPROCATING AND CENTRIFUGAL COMPRESSORS Takao Ohama, Takao Koga, Yoshinori Kurioka, Hironao Tanaka 89 LECTURES
TAMU Turbo Show 2006 RADAR-BASED SENSORS—A NEW TECHNOLOGY FOR REAL-TIME, DIRECT TEMPERATURE MONITORING OF CRANK AND CROSSHEAD BEARINGS OF DIESELS AND HAZARDOUS MEDIA RECIPROCATING COMPRESSORS Steinar Fossen, Edward Gemdjian 97 LECTURES
TAMU Turbo Show 2006 HIGH SPEED MOTOR DESIGN FOR GAS COMPRESSOR APPLICATIONS Paul Beer, John Tessaro, Brian Eckels, Paul Gaberson 103 TUTORIALS
TAMU Turbo Show 2006 WHAT’S CORRECT FOR MY APPLICATION—A CENTRIFUGAL OR RECIPROCATING COMPRESSOR? Paul Gallick, Greg Phillippi, Benjamin F. Williams 113 TUTORIALS
TAMU Turbo Show 2006 SURGE AVOIDANCE FOR COMPRESSOR SYSTEMS R.C. White, Rainer Kurz 123 TUTORIALS
TAMU Turbo Show 2006 GUIDELINES FOR SPECIFYING AND EVALUATING THE RERATING AND REAPPLICATION OF STEAM TURBINES Donald H. Mansfield, Douglas W. Boyce, William G. Pacelli 135 TUTORIALS
TAMU Turbo Show 2006 API SPECIFICATION REVIEW FOR GAS TURBINE DRIVEN TURBOCOMPRESSORS Klaus Brun, Jeff Moore 145 TUTORIALS
TAMU Turbo Show 2006 TORSIONAL VIBRATION—A SEGMENT OF API 684 Jim Hudson, Troy Feese 155 TUTORIALS
TAMU Turbo Show 2007 SURVEYING TILTING PAD JOURNAL BEARING AND GASLABYRINTH SEAL COEFFICIENTS AND THEIR EFFECT ON ROTOR STABILITY John A Kocur, John C. Nicholas, Chester C. Lee 1 Lectures
TAMU Turbo Show 2007 ROTOR BEARING LOADS WITH HONEYCOMB SEALS AND VOLUTE FORCES IN REINJECTION COMPRESSORS Leonardo Baldassare, John W Fulton 11 Lectures
TAMU Turbo Show 2007 IMPROVING THE RELIABILITY OF A HIGH SPEED REFRIGERATION COMPRESSOR Ray D. Keirn, Malcolm E. Leader 21 Lectures
TAMU Turbo Show 2007 STUDY OF A ROTORDYNAMIC ANALYSIS METHOD THAT CONSIDERS TORSIONAL AND LATERAL COUPLED VIBRATIONS IN COMPRESSOR TRAINS WITH A GEARBOX Masayuki Kita, Takeski Hataya, Yasunori Tokimasa 31 Lectures
TAMU Turbo Show 2007 REDESIGN OF A HIGH SPEED COMPRESSOR DRIVE STEAM TURBINE TO OVERCOME CAPACITY, EFFICIENCY, AND RELIABILITY ISSUES Richard G. Olivier, Hayden Brown 39 Lectures
TAMU Turbo Show 2007 PIPELINE STAGE DESIGN FOR INCREASED OPERATING RANGE Gilles Nawrocki, Denis Guenard, Vittorio Michelassi 45 Lectures
TAMU Turbo Show 2007 DEVELOPMENT OF A SYSTEM FOR LEAN, PREVAPORIZED, PREMIXED COMBUSTION Richard J Roby, Michael S. Klassen, Leo Eskin, Michael Ramotowski, Glenn Gaines 55 Lectures
TAMU Turbo Show 2007 ELECTRIC SYSTEMS FOR HIGH POWER COMPRESSOR TRAINS IN OIL AND GAS APPLICATIONS-SYSTEM DESIGN, VALIDATION APPROACH, AND PERFORMANCES Roberto Baccani, Richard Zhang, Tommaso Toma, Andrea Iuretig, Mauro Perna 61 Lectures
TAMU Turbo Show 2007 ANALYSIS OF VIBRATORY STRESS OF INTEGRAL SHROUD BLADE FOR MECHANICAL DRIVE STEAM TURBINE Yasutomo Kaneko, Kazushi Mori, Toshihiro Miyawaki, Satoshi Hata 69 Lectures
TAMU Turbo Show 2007 ON THE POTENTIAL OF METAL AND CERAMIC BASED ABRADABLES IN TURBINE SEAL APPLICATIONS Dieter Sporer, Scott Wilson, Iacopo Giovannetti, Arno Refke, Massimo Giannozzi 79 Lectures
TAMU Turbo Show 2007 ASME PTC-lO MODIFIED TEST FOR MECHANICAL ASSESSMENT OF CENTRIFUGAL COMPRESSORS Marcelo Accorsi Miranda, Roberto Firmento de Noronha 87 Lectures
TAMU Turbo Show 2007 APPLICATION OF DYNAMIC SIMULATION IN THE DESIGN, OPERATION, AND TROUBLESHOOTING OF COMPRESSOR SYSTEMS Vinod Patel, Jeffery Feng, Surajit Dasgupta, Prakash Ramdoss, Jihong Wu 97 Lectures
TAMU Turbo Show 2007 RECIPROCATING COMPRESSOR CONDITION MONITORING Steven M Schultheis, Charles A. Lickteig, Robert Parchewsky 107 Turorials
TAMU Turbo Show 2007 GAS TURBINES AND TURBOCOMPRESSORS FOR LNG SERVICE Cyrus B. Meher-Homji, Terryl Matthews, Antonio Pelagotti, Hans P. Weyermann 115 Turorials
TAMU Turbo Show 2007 A PRACTICAL GUIDELINE FOR A SUCCESSFUL ROOT CAUSE FAILURE ANALYSIS David L. Ransom 149 Turorials
TAMU Turbo Show 2007 ADVANCES IN GAS TURBINE COUPLINGS Joseph P. Corcoran, Douglas Lyle, Patrick McCormack, Tim Ortel 157 Turorials
TAMU Turbo Show 2007 MAINTENANCE AND OPERATING PRACTICES EFFECTS ON DEGRADATION AND LIFE Ranier Kurz, Klaus Brun 173 Turorials
TAMU Turbo Show 2007 REFINING FUNDAMENTALS Michael D. Morris 187 Turorials
TAMU Turbo Show 2008 TILTING PAD JOURNAL BEARING STARVATION EFFECTS John C. Nicholas, Greg Elliott, Thomas P Shoup, Ed Martin 1 LECTURES
TAMU Turbo Show 2008 JOURNAL BEARING VIBRATION AND SSV HASH Scan M DeCamillo, Minhui He, C. Hunter Cloud 11 LECTURES
TAMU Turbo Show 2008 INVESTIGATION OF CORROSION FATIGUE PHENOMENA IN TRANSIENT ZONE AND PREVENTIVE COATING AND BLADE DESIGN AGAINST FOULING AND CORROSIVE ENVIRONMENT FOR MECHANICAL DRIVE TURBINES Satoshi Hata, Naoyuki Nagai, Toyoaki Yasui, Hiroshi Tsukamoto 25 LECTURES
TAMU Turbo Show 2008 DESIGN AND MITIGATION TECHNIQUES FOR APPLICATIONS WITH POSSIBLE LIQUID CONTAMINATION OF THE SEALING GAS DRY GAS SEAL SYSTEM James R McCraw, Vladimir Bakalchuk, Richard Hosanna 37 LECTURES
TAMU Turbo Show 2008 TORSIONAL VIBRATION PROBLEM WITH MOTOR/ID FAN SYSTEM DUE TO PWM VARIABLE FREQUENCY DRIVE Troy Freese, Ryan Maxfield 45 LECTURES
TAMU Turbo Show 2008 TORSIONAL INTERHARMONIC INTERACTION STUDY OF 75 MW DIRECT-DRIVEN VSDS MOTOR COMPRESSOR TRAINS FOR LNG DUTY Volker Hutten, Rainer M Zurowski, Martin Hilscher 57 LECTURES
TAMU Turbo Show 2008 A NEW METHOD OF ACCURATELY IDENTIFYING THE LOCATION AND MOVEMENT OF FORWARD AND BACKWARD BENDING MODES USING MAGNETICALLY SUSPENDED ROTOR SYSTEMS Jigger Jumonville 67 LECTURES
TAMU Turbo Show 2008 WORLD'S FIRST 10,000 PSI SOUR GAS INJECTION COMPRESSOR Bruce L. Hopper, Leonardo Baldassarre, Irvin Detiveaux, John W Fulton, Peter C. Rasmussen, Alberto Tesei, Jim Demetriou, Sam Mishael 73 LECTURES
TAMU Turbo Show 2008 PREDICTION OF SUBSYNCHRONOUS ROTOR VIBRATION AMPLITUDE CAUSED BY ROTATING STALL Masayuki Kita, Shinji Iwamoto, Daisuke Kiuchi, Katsuya Yamashita, Rinpei Kawashita 97 LECTURES
TAMU Turbo Show 2008 LIFE CYCLE ASSESSMENT OF TURBOMACHINERY FOR OFFSHORE APPLICATIONS-UPDATED WITH FIELD DATA Marcelo Accorsi Miranda, Orlando Guerreiro Meira 103 LECTURES
TAMU Turbo Show 2008 A DNV MODELED QUALIFICATION PROCESS FOR A TURBOCOMPRESSOR INCORPORATING A ROTARY SEPARATOR KNOWN AS THE INTEGRATED COMPRESSION SYSTEM Gocha Chochua, Jose L. Gilarranz. H Allan Kidd, Wuuam Maier 111 LECTURES
TAMU Turbo Show 2008 DYNAMIC INSTABILITIES IN INDUSTRIAL COMPRESSION SYSTEMS WITH CENTRIFUGAL COMPRESSORS Kamal K. Botros, Subramaniam T. Ganesan 119 LECTURES
TAMU Turbo Show 2008 ROTORDYNAMIC DESIGN AUDITS OF AMB SUPPORTED MACHINERy Erik E. Swanson, Eric H Maslen, Guoxin Li, C. Hunter Cloud 133 TUTORIALS
TAMU Turbo Show 2008 THE SYNCHRONOUS ROTOR INSTABILITY PHENOMENON-MORTON EFFECT Frits M de Jongh 159 TUTORIALS
TAMU Turbo Show 2008 EMERGING ADVANCED TECHNOLOGIES TO ASSESS RELIABILITY OF INDUSTRIAL STEAM TURBINE BLADE DESIGN Murari P Singh, Michael J. Drosjack 169 TUTORIALS
TAMU Turbo Show 2008 SELECTION OF MATERIALS AND MATERIAL RELATED PROCESSES FOR CENTRIFUGAL COMPRESSORS AND STEAM TURBINES IN THE OIL AND PETROCHEMICAL INDUSTRy Phillip Dowson, Derrick Bauer, Scot Laney 189 TUTORIALS
TAMU Turbo Show 2008 STEAM TURBINE CORROSION AND DEPOSITS-PROBLEMS AND SOLUTIONS Otakar Jonas, Lee Machemer 211 TUTORIALS
TAMU Turbo Show 2009 DEVELOPMENT AND APPLICATION OF A VERTICAL HIGH SPEED MOTOR-COMPRESSOR SIMULATOR FOR ROTOR DROP ONTO AUXILIARY BEARINGS David Ransom, Andrea Masala, Jeffrey Moore, Giuseppe Vannini, Massimo Camatti, Michel Lacour 1 LECTURES
TAMU Turbo Show 2009 TRANSIENT SURGE MEASUREMENTS OF A CENTRIFUGAL COMPRESSOR STATION DURING EMERGENCY SHUTDOWNS J Jeffrey Moore, Augusto Garcia-Hernandez, Matthew Blieske, Rainer Kurz, Klaus Brun 13 LECTURES
TAMU Turbo Show 2009 MECHANICAL AND PERFORMANCE TESTING METHOD OF AN INTEGRATED HIGH-SPEED MOTOR COMPRESSOR Thomas Alban, Olivier Pellerin, Pierre Laboube, Bernard Quoix, Alain Gelin, Matthieu Oliva 27 LECTURES
TAMU Turbo Show 2009 KNOWLEDGE-BASED TOOL DEVELOPMENT AND DESIGN FOR RECIPROCATING COMPRESSORS Brian Howard, John A. Kocur, Jr. 41 LECTURES
TAMU Turbo Show 2009 INVESTIGATIONS ON THE DYNAMIC COEFFICIENTS OF IMPELLER EYE LABYRINTH SEALS Norbert G, Wagner, Klaus Steff, Rainer Gausmann, Marcus Schmidt 53 LECTURES
TAMU Turbo Show 2009 FULL-SCALE AERODYNAMIC AND ROTORDYNAMIC TESTING FOR LARGE CENTRlFUGAL COMPRESSORS James M. Sorokes, Thomas A. Soulas, Jay M Koch, Jose L. Gilarranz 71 LECTURES
TAMU Turbo Show 2009 TORSIONAL MODE DAMPING FOR ELECTRICALLY DRIVEN GAS COMPRESSION TRAINS IN EXTENDED VARIABLE SPEED OPERATION Christof Sihler, Simon Schramm, Joseph Song-Manguelle, Paola Rotondo, Stefano Del Puglia, Einar Larsen 81 LECTURES
TAMU Turbo Show 2009 COMBINED TORSIONAL AND ELECTROMECHANICAL ANALYSIS OF AN LNG COMPRESSION TRAIN WITH VARIABLE SPEED DRIVE SYSTEM Paola Rotondo, Davide Andreo, Stefano Falomi, Pieder Jorg, Andrea Lenzi, Tim Hattenbach, Duccio Fioravanti, Sergio De Franciscis 93 LECTURES
TAMU Turbo Show 2009 AEROACOUSTIC PHENOMENA IN HIGH PRESSURE CENTRIFUGAL COMPRESSORS - A POSSIBLE ROOT CAUSE FOR IMPELLER FAILURES Sven Konig, Nico Petry, Norbert Wagner 103 LECTURES
TAMU Turbo Show 2009 ASSESSING LIQUID DROPLET EROSION POTENTIAL IN CENTRIFUGAL COMPRESSOR IMPELLERS Jorge Pacheco, H. Allan Kidd 123 LECTURES
TAMU Turbo Show 2009 VERIFICATION FULL LOAD TEST OF 1,980,000 LB/H LARGE MECHANICAL DRIVE STEAM TURBINE FOR ASU UP TO 200 MW BASED ON PRINCIPLE OF HIGH SCALE MODEL SIMILARITY Osamu Isumi, Takashi Niiyama, Kazushi Mori, Satoshi Hata 129 LECTURES
TAMU Turbo Show 2009 DESIGN AND EXPERIMENTAL EVALUATION OF A HIGH-SPEED, DIRECTLY-COUPLED, MULTI-MEGAWATT PERMANENT-MAGNET MACHINE Cassandra Bailey, Daniel M. Saban, Delvis Gonzalez-Lopez 137 LECTURES
TAMU Turbo Show 2009 DRY SCREW COMPRESSOR PERFORMANCE AND APPLICATION RANGE Jurgen Wennemar 149 TUTORIALS
TAMU Turbo Show 2009 TURBINE OVERSPEED SYSTEMS AND REQUIRED RESPONSE TIMES Scott L. Taylor, Sheldon S. Smith 157 TUTORIALS
TAMU Turbo Show 2009 CENTRIFUGAL COMPRESSOR APPLICATIONS-UPSTREAM AND MIDSTREAM Peter C. Rasmussen, Rainer Kurz 169 TUTORIALS
TAMU Turbo Show 2009 SELECTION OF MATERIALS AND MATERIAL RELATED PROCESSES FOR FCC POWER RECOVERY TURBINES Phillip Dowson, David Dowson 187 TUTORIALS
TAMU Turbo Show 2009 PREVENTION OF TORSIONAL VIBRATION PROBLEMS IN RECIPROCATING MACHINERY Troy Feese, Charles L. Hill 213 TUTORIALS
TAMU Turbo Show 2009 THE EFFECTS OF PULSATIONS ON THE SURGE MARGIN OF CENTRIFUGAL COMPRESSORS IN STATIONS WITH BOTH RECIPROCATING AND CENTRIFUGAL COMPRESSORS Klaus Brun, Rainer Kurz 239 SPECIAL PAPERS
TAMU Turbo Show 2009 ROTORDYNAMIC STABILITY OF A 9500 PSI REINJECTION CENTRIFUGAL COMPRESSOR EQUIPPED WITH A HOLE PATTERN SEAL-MEASUREMENT VERSUS PREDICTION TAKING INTO ACCOUNT THE OPERATIONAL BOUNDARY CONDITIONS Yves Bidaut, Urs Baumann, Salim Mohamed Hamed AI-Harthy 251 SPECIAL PAPERS
TAMU Turbo Show 2009 STUDY OF LARGE VSI DRIVE SYSTEM FOR THE OIL AND GAS INDUSTRY Masahiko Tsukakoshi, Mostafa Al Mamun, Kazunori Hashimura, Hiromi Hosoda 261 SPECIAL PAPERS
TAMU Turbo Show 2009 PIPING FORCES AND MOMENTS ON COMPRESSORS AND STEAM TURBINES Katsuki Yagi, Atsushi Higashio, Hirokazu Kawashima 267 SPECIAL PAPERS
TAMU Turbo Show 2010 MODELING OF ROTOR BOW DURING HOT RESTART IN CENTRIFUGAL COMPRESSORS Leonardo Baldassarre, Michele Fontana 1 LECTURE
TAMU Turbo Show 2010 WACHEL’ S EQUATION— ORIGIN AND CURRENT EVALUATION OF API 617 ROTOR STABILITY SCREENING CRITERIA B. Fred Evans, John W Fulton 9 LECTURE
TAMU Turbo Show 2010 MEASUREMENT OF DYNAMIC PERFORMANCE OF LARGE TILTING PAD JOURNAL BEARING AND ROTOR STABILITY IMPROVEMENT Kyouichi Ikeno, Yuichi Sasaki, ]?you Kawabata, Satoru Yoshida, Satoshi Hata 19 LECTURE
TAMU Turbo Show 2010 SHOP ACCEPTANCE TESTING OF COMPRESSOR ROTORDYNAMIC STABILITY AND THEORETICAL CORRELATION Brian C. Pettinato, C. Hunter Cloud, ]?ogerio S. Campos 31 LECTURE
TAMU Turbo Show 2010 DYNAMIC STRESS MEASUREMENT OF CENTRIFUGAL COMPRESSOR IMPELLER AND STUDY FOR STRENGTH CRITERIA BASED ON CORRELATION BY UNSTEADY CFD Atsushi Higashio, Hiroyuki Yamashita, Mitsuhiko Ota 43 LECTURE
TAMU Turbo Show 2010 UNSTEADY FLOW FIELD MEASUREMENTS IN AN INDUSTRIAL CENTRIFUGAL COMPRESSOR Lorenzo Toni, Valeria Ballarini, Stefano Cioncolini, Paolo Gaetani, Giacomo Persico 49 LECTURE
TAMU Turbo Show 2010 CENTRIFUGAL COMPRESSOR EVOLUTION James M Sorokes, MarkJ Kuzdzal 59 LECTURE
TAMU Turbo Show 2010 DESIGN OPTIMIZATION AND TESTING OF COMBINED CENTRIFUGAL SEPARATION AND COMPRESSION TECHNOLOGY William Maier, Yuri Biba 71 LECTURE
TAMU Turbo Show 2010 APPLICATION OF REPAIRS TO TURBOMACHINERY EQUIPMENT IN OIL REFINERY, CHEMICAL, AND POWER GENERATION PLANTS David Dowson, Phillip Dowson 79 LECTURE
TAMU Turbo Show 2010 ENHANCING PERFORMANCE OF MATERIALS IN TURBOMACHINERY: A REVIEW OF COATING AND SURFACE MODIFICATION TECHNOLOGIES Scot Laney, Derrick Bauer 91 LECTURE
TAMU Turbo Show 2010 AN ENGINE DRIVEN, HIGH PRESSURE RECIPROCATING TYPE INJECTION GAS COMPRESSOR DESIGN Gary A. Ehlers, Kurt Haaland 113 LECTURE
TAMU Turbo Show 2010 DRAMATIC REDUCTION OF GAS TURBINE FOULING WITH HEPA COMPOSITE MEMBRANE AIR INTAKE FILTERS Wilson Poon, Matthew Gessner Steven Medvetz 129 LECTURE
TAMU Turbo Show 2010 PREVENTING UNDETECTED TRAIN TORSIONAL OSCILLATIONS Joseph P Corcoran, John A. Kocur Ji, Michael C. Mitsingas 135 TUTORIAL
TAMU Turbo Show 2010 TUTORIAL ON CRYOGENIC TURBOEXPANDERS Jigger Jumonville 147 TUTORIAL
TAMU Turbo Show 2010 GAS TURBINE FUELS—SYSTEM DESIGN, COMBUSTION, AND OPERABILITY Cyrus B. Meher-Homji, Justin Zachary, Andrew F Bromley 155 TUTORIAL
TAMU Turbo Show 2010 PROTECTIVE SYSTEMS FOR TURBOMACHIERY— WHAT IS THE RIGHT LEVEL? HOW TO VERIFY? Stephen 1?. Locke, Curt Miller, Lii Kassie 187 TUTORIAL
TAMU Turbo Show 2010 AERODERIVATIVE, iNDUSTRIAL, AND LIGHT INDUSTRIAL GAS TURBINES—A COMPARISON Jeff Haught 189 TUTORIAL
TAMU Turbo Show 2010 NOVEL TORQUE RIPPLE MINIMIZATION CONTROL FOR 25 MW VARIABLE SPEED DRIVE SYSTEM FED BY MULTILEVEL VOLTAGE SOURCE INVERTER Masahilco Tsulcalcoshi, Mostafa Al Mamun, Kazunori Hashimura, Hiromi Hosoda, Junichi Sakaguchi, Lazhar Ben-B rahim 193 SPECIAL PAPER
TAMU Turbo Show 2010 Prevention of Shaft End Damage Due to High Contact Pressure Raymond Vollmer, Goodrich Corp., Rome, NY, Satoru Yoshida, Mitsubishi Heavy Industries, Ltd., Hiroshima, Japan, Monica Crowe, Goodrich Corp. Rome, NY, and Hiroki Terado, Mitsubishi Heavy Industries, Ltd., Hiroshima, Japan 1 Case Study
TAMU Turbo Show 2010 Investigation and Elimination of Aerodynamically Induced Torsional Vibrations on an Integrally-Geared Centrifugal Compressor René Rose Stueber, Christoph Beckers, Atlas Copco Energas GmbH, Cologne, Germany, Ruzbeh Homji, Chevron Energy Technology Co., Houston, TX, and Juan Carlos Rivadeneira, Bechtel Corp., Houston, TX 2 Case Study
TAMU Turbo Show 2010 Is Frame Vibration Enough Protection? Early Detection of a Wrist Pin Failure Using Crosshead Vibration Rob van Ijzendoorn, BP Refining & Logistics Technology, Rotterdam, Netherlands, and Skip Morrison, PROGNOST Systems, Inc., Houston, TX 3 Case Study
TAMU Turbo Show 2010 High Motor Vibration on a Screw Compressor Linked to Natural Frequency Excitation Matthew Taylor, DuPont Washington Works, Washington, WV, and José A. Vázquez, DuPont, Wilmington, DE 4 Case Study
TAMU Turbo Show 2010 Journal Bearing Upgrade to Solve Reliability Issues in an Accessory Gearbox John K. Whalen, TCE/Turbo Components & Engineering, Inc., Houston, TX, and Lorenzo Aburto, ConocoPhillips Alaska 5 Case Study
TAMU Turbo Show 2010 Load Dependent Critical Speed Gregory L. Elliott, Lufkin Industries, Inc., Lufkin, TX, James F. McCraw, BP America, Inc., Houston, TX, and Thomas P. Shoup, Lufkin-RMT, Wellsville, NY 6 Case Study
TAMU Turbo Show 2010 Gearbox Failures Due to Bull Gear Slippage Roberto Firmento de Noronha, Dione Alves de Sousa, and Fabio de Normal et d'Audenhove, PETROBRAS, Rio de Janeiro, Brazil 7 Case Study
TAMU Turbo Show 2011 A ROOT CAUSE FAULURE ANALYSIS FOR RECURRING IMPELLER FAILURES IN A 4.7 MM TON LNG TRAIN PROPANE COMPRESSOR Nicholas M. White, Scot J. Laney, and Cory Zorzi Lecture
TAMU Turbo Show 2011 ON-SITE DETERMINATION OF THE CONTROL LINE FOR INTEGRALLY GEARED COMPRESSORS FOR AVOIDANCE OF IMPELLER FATIGUE FAILURES Norbert G. Wagner, Georg Winkes, Sven König, Stefan Süß Lecture
TAMU Turbo Show 2011 TILTING-PAD BEARINGS: MEASURED FREQUENCY CHARACTERISTICS OF THEIR ROTORDYNAMIC COEFFICIENTS Dara Childs, Adolfo Delgado, and Giuseppe Vannini Lecture
TAMU Turbo Show 2011 DEVELOPMENT OF A HIGH PRESSURE ROTORDYNAMIC TEST RIG FOR CENTRIFUGAL COMPRESSORS INTERNAL SEALS CHARACTERIZATION Giuseppe Vannini, Stefano Cioncolini, Vincenzo Calicchio, and Francesco Tedone Lecture
TAMU Turbo Show 2011 NEW APPROACH TO TORSIONAL VIBRATION MONITORING Lorenzo Naldi, Mateusz Golebiowski, and Valerio Rossi Lecture
TAMU Turbo Show 2011 DEMONSTRATION OF THE ROTORDYNAMIC EFFECTS OF CENTRIFUGAL LIQUID SEPARATION AND GAS COMPRESSION IN AN OIL-FREE INTEGRATED MOTOR-COMPRESSOR Tim Griffin and William Maier Lecture
TAMU Turbo Show 2011 FULL LOAD TESTING OF A 12.5 MW VERTICAL HIGH SPEED SUBSEA MOTORCOMPRESSOR Giuseppe Vannini, Andrea Masala, Massimo Camatti, Massimiliano Ortiz Neri, Sergio Bondi, and Silvia Evangelisti Lecture
TAMU Turbo Show 2011 LONG TERM OPERATING EXPERIENCE WITH CORROSION CONTROL IN INDUSTRIAL AXIAL FLOR COMPRESSORS David Linden Lecture
TAMU Turbo Show 2011 DEVELOPMENT OF ADVANCED CENTRIFUGAL COMPRESSORS AND PUMPS FOR CARBON CAPTURE AND SEQUESTRATION APPLICATIONS J. Jeffrey Moore, Andrew Lerche, Hector Delgado, Tim Allison, and Jorge Pacheco Lecture
TAMU Turbo Show 2011 MECHANICAL PERFORMANCE OF A TWO STAGE CENTRIFUGAL COMPRESSOR UNDER WET GAS CONDITIONS David Ransom, Luigi Podesta, Massimo Camatti, Melissa Wilcox, Matteo Bertoneri, and Manuele Bigi Lecture
TAMU Turbo Show 2011 OPERATION OF CENTRIFUGAL COMPRESSORS IN CHOKE CONDITIONS Rainer Kurz, Russell K. Marechale, Edward J. Fowler, Min Ji, and Michael J. Cave Lecture
TAMU Turbo Show 2011 MODELING AND PREDICTION OF SIDESTREAM INLET PRESSURE FOR MULTISTAGE CENTRIFUGAL COMPRESSORS Moulay Belhassan, Jay Koch, and James M. Sorokes Lecture
TAMU Turbo Show 2011 GAS SEAL CONTAMINATION Raphael Bridon and Olivier Lebigre Tutorial
TAMU Turbo Show 2011 RANGE VS. EFFICIENCY—STRIKING THE PROPER BALANCE James M. Sorokes Tutorial
TAMU Turbo Show 2011 PULSATION, VIBRATION, AND NOISE ISSUES WITH WET AND DRY SCREW COMPRESSORS Donald R. Smith Tutorial
TAMU Turbo Show 2011 GUIDELINES FOR REDUCING THE NOISE LEVEL OF A CENTRIFUGAL AIR COMPRESSOR INSTALLATION John R. Badini and Paul A. Brown Tutorial
TAMU Turbo Show 2011 INTRODUCTION TO ENGINEERING ETHICS WITH ROTATING MACHINERY CASE STUDIES Robert X. Perez Tutorial
TAMU Turbo Show 2011 BUYING/SELLING SERIAL NUMBER ONE Michael Drosjack, Harry F. Miller, and James M. Sorokes Tutorial
TAMU Turbo Show 2011 STABILITY CONSIDERATIONS: A SIMPLIFIED APPROACH Urs Baumann Tutorial
TAMU Turbo Show 2011 SUCCESSFUL SELECTION AND OPERATION OF GAS TURBINE INLET FILTRATION SYSTEMS Melissa Wilcox, Rainer Kurz, and Klaus Brun Tutorial
TAMU Turbo Show 2011 CO2 CAPTURE AND PUMPING Ron Adams Tutorial
TAMU Turbo Show 2011 Reliability Improvement for Reciprocating Compressor Valve in CCR Reformer Lee Sang Suk Case Study
TAMU Turbo Show 2011 Reliability improvements on high speed reciprocating compressors through bearing and process modifications Jim Cencula, Carlo Mazzali, Vinh Do, Ray Gallagher, Greg Bone Case Study
TAMU Turbo Show 2011 Higher reliability of oil operated bolt tensioner for larger-sized steam turbine casings with higher inlet steam pressure Kyoichi Ikeno Case Study
TAMU Turbo Show 2011 In-house Engineering for Resolution of Chronic 4th Stage High Discharge Pressure Limitation on Carbon-dioxide Reciprocating Compressor Ali Shallwani Case Study
TAMU Turbo Show 2011 Balance Instability and Vibration on a 6 MW Induction motor Rotor Gunnar Prosby, Sameer S. Patwardhan, Siddharth (Sid) Shinde, Barry Wood Case Study
TAMU Turbo Show 2011 Advanced Vibration Analysis on Gear Box Train and vibration elimination Udayashankar P. Eng. Case Study
TAMU Turbo Show 2011 Vibration and Balance Issues Resulting from Keyway Fitting Mark O’Neil Case Study
TAMU Turbo Show 2011 Investigation of Engine Vibration for Natural Gas Gathering and Transmission Troy Feese Case Study
TAMU Turbo Show 2011 Correction of Chronic Thrust Bearing Failures on a Refrigeration Compressor Matthew D. Moll, Julia Postill Case Study
TAMU Turbo Show 2011 Turbo-Expander Compressor Active Magnetic Bearing Trips Reduction - A Case Study Chong Ong, Jim Cencula, Randy Wu, Marcin Bielecki, Matthias Lelanno Case Study
TAMU Turbo Show 2011 Speed Signal Deterioration at High Speeds in Electronic Governor and Trip Systems Bryan Barrington Case Study
TAMU Turbo Show 2011 Reverse Rotation in Centrifugal Compressors Amr Gad Case Study
TAMU Turbo Show 2011 “Beating” Effect Caused by Two Closely Spaced Mechanical Frequencies Observed on Two Shaft, Gas Turbine Drive Robert X. Perez, Andrew Conkey Case Study
TAMU Turbo Show 2011 Coupled Sub-Synchronous Vibration of Lateral and Axial Directions Daisuke Kiuchi Case Study
TAMU Turbo Show 2011 Thermoplastic Labyrinth Seals in Centrifugal Compressors -15 years of experiences John K. Whalen, Jim Allen, Jonathan D. Cardell, John R. Dugas Case Study
TAMU Turbo Show 2012 Analysis Of Solid Particle Surface Impact Behavior In Turbomachines To Assess Blade Erosion And Fouling Klaus Brun, Ph.D., Marybeth Nored, Rainer Kurz, Ph.D. Lecture 01
TAMU Turbo Show 2012 Valve Performance And Life Of Reciprocating Compressors Klaus Brun, Ph.D., Marybeth Nored Lecture 02
TAMU Turbo Show 2012 Fixed Speed Compressors Operation In Offshore Production Platforms Fabio de Norman et d'Audenhove, Andre Varella Guedes (MSc), Michel Stathakis Neto (MSc), Bruno da Silva Marques (MSc) Lecture 03
TAMU Turbo Show 2012 'C' Type Ptfe Gaskets Performances In High Pressure Sour Applications Leonardo Baldassarre,Marco Pelella Lecture 04
TAMU Turbo Show 2012 Steady State Performance Prediction Of Directly Lubricated Fluid Film Journal Bearings Minhui He, James M. Byrne, C. Hunter Cloud, José A. Vázquez Lecture 05
TAMU Turbo Show 2012 Early Detection Of Rotating Stall Phenomenon In Centrifugal Compressors By Means Of Asme Ptc 10 Type 2 Test Leonardo Ishimoto, Raphael Timbó Silva, Joilson de Souza Rangel Junior, Marcelo Accorsi Miranda, Fabio de Norman Et Audehove, Bruno da Silva Marques, Leonardo Baldassarre, Christophe Puaut Lecture 06
TAMU Turbo Show 2012 A Comparison of Manufacturing Methods, Accuracy, Quality Control and Testing Methods a They Relate to High Head Low Flow Impeller Efficiency and Overall Compressor Performance Nathan Pash, George C. Hayles, Jr., Daisuke Hirata, Daisuke Kiuchi Lecture 07
TAMU Turbo Show 2012 Impact Of Electrical Noise On The Torsional Response Of Vfd Compressor Trains John A. Kocur, Jr. Ph.D., Maximilian G. Muench M.S. Lecture 08
TAMU Turbo Show 2012 Co2 Compression At World's Largest Carbon Dioxide Injection Project Antonio Musardo, Marco Pelella, Vinod Patel, Mark Weatherwax, Gabriele Giovani, Sergio Cipriani Lecture 09
TAMU Turbo Show 2012 Centrifugal Stage Performance Prediction And Validation For High Mach Number Applications Steven C. Kowalski, Jorge E. Pacheco, PhD, Syed Fakhri, James M. Sorokes Lecture 10
TAMU Turbo Show 2012 New Advances In Pulse Width Modulated Slip Power Recovery Drives For Pumps Evaluation of Bearing Designs for a Multistage Centrifugal Compressor Using a Magnetic Exciter Donghui Zhang, Wolfgang Faller, Chester Lee Lecture PNP
TAMU Turbo Show 2012 Gas Seal Contamination Raphael Bridon, Olivier Lebigre Tutorial 01
TAMU Turbo Show 2012 Range Versus Efficiency – Striking The Proper Balance James M. Sorokes Tutorial 02
TAMU Turbo Show 2012 Pulsation, Vibration, And Noise Issues With Wet and Dry Screw Compressors Donald R. Smith Tutorial 03
TAMU Turbo Show 2012 Introduction To Engineering Ethics With Rotating Machinery Case Studies obert X. Perez Tutorial 04
TAMU Turbo Show 2012 Buying / Selling Serial #1 ichael J. Drosjack, Ph.D., Harry F. Miller, James M. Sorokes Tutorial 05
TAMU Turbo Show 2012 Simplified Modal Analysis For The Plant Machinery Engineer José A. Vázquez, C. Hunter Cloud, Robert J. Eizember Tutorial 06
TAMU Turbo Show 2012 Gas Turbine Performance And Maintenance Rainer Kurz, Klaus Brun, Cyrus Meher-Homji, Jeff Moore Tutorial 07
TAMU Turbo Show 2012 Babbitted Bearing Health Assessment John K. Whalen, P.E., Jim Allen, Thomas D. Hess, Jr., P.E., Jack Craighton, CLS Tutorial 08
TAMU Turbo Show 2012 VSDS Motor Inverter Design Concept For Compressor Trains Avoiding Interharmonics In Operating Speed Range Volker Hütten, Christian Beer, Tim Krause, Sven Demmig Tutorial 09
TAMU Turbo Show 2012 Torsional Natural Frequencies: Measurement Vs. Prediction Qingyu Wang, Troy D. Feese, Brian C. Pettinato Tutorial 10
TAMU Turbo Show 2012 Comparison Of Different Variable Speed Compression Train Configurations With Respect To Rotordynamic Stability And Torsional Integrity Reto Somaini, Baumann Urs, Yves Bidaut Tutorial PNP
TAMU Turbo Show 2013 Torsional and Electrical Dynamic Interactions of Compressor Drive Motors and Gas Turbine Driven Power Generators Fred Evans (ExxonMobil Development Company, Houston, TX), Brandon Cassimere (ExxonMobil Upstream Research, Houston, TX), Don E Martin (ABB Inc., Raleigh, NC), E. Martin Hinchliff (Dresser-Rand Company, NY), Danny F. Smith (Solar Turbines Incorporated, CA) Lecture T1
TAMU Turbo Show 2013 Experimental Evaluation of Effectiveness of Online Water-Washing in Gas Turbine Compressors Klaus Brun (Southwest Research Institute, San Antonio, TX), Terrence A. Grimley (Southwest Research Institute, San Antonio, TX), William C. Foiles (BP Exploration & Production, Houston, TX), Rainer Kurz (Solar Turbines, Inc., San Diego, CA) Lecture T2
TAMU Turbo Show 2013 Limitations of ASME PTC 10 in Accurately Evaluation Centrifugal Compressor Thermodynamic Performance Mark Sandberg (Chevron Energy Technology Co., Houston, TX), Gary Colby (Dresser-Rand, Olean, NY) Lecture T3
TAMU Turbo Show 2013 Probabilistic Approach for Compressor Sizing and Plant Design Rainer Kurz (Solar Turbines Incorporated, San Diego, CA), Klaus Brun (Southwest Research Institute, San Antonio, TX), J. Michael Thorp (Aramco Services Company, Houston, TX), Erik G. Zentmyer (Solar Turbines Incorporated, Houston, TX) Lecture T4
TAMU Turbo Show 2013 Investigation Results for Surge Phenomena of Centrifugal Compressor related with Piping Arrangements and Test Conditions Daisuke Kiuchi (Mitsubishi Heavy Industries Compressor Corp., Tokyo), Akihiro Nakaniwa (Mitsubishi Heavy Industries, Ltd., Hyogo, Japan), Shinichiro Tokuyama (MHI Compressor Corporation, Hiroshima, Japan), Keisuke Matsuyama (Mitsubishi Heavy Industries, Ltd., Japan) Lecture T5
TAMU Turbo Show 2013 LNG Propane Compressor Performance Prediction and Large scale Test Validation Jorge Pacheco (Dresser-Rand, Olean, NY), Syed Fakhri (Dresser-Rand, Olean, NY), Clémentine Vezier (Dresser-Rand, Olean, NY), Jay Koch (Dresser-Rand, Olean, NY) Lecture T6
TAMU Turbo Show 2013 Electric Driven Centrifugal Compressor - Super Synchronous Vibrations of the High Speed Shaft Line Observations, Assessment and Resolution, Bernard Quoix (TOTAL E&P, France), Antoine Lucas (TOTAL E&P, Korea), Jeremie Seon (GE Oil&Gas, France), Xavier Coudray (GE Oil&Gas, France), Alain Gelin (TOTAL E&P, France) Lecture T7
TAMU Turbo Show 2013 Coupling Credible Failure Modes and Owner Options to Intervene Stephen Locke (DuPont, Old Hickory, TN), Michael Burgess (DuPont, Old Hickory, TN), Joseph Corcoran (Kop-Flex, Emerson Industrial Automation, MD), Thomas Hess (DuPont, Wilmington, DE) Lecture T8
TAMU Turbo Show 2013 Review of Experimental Sub-Synchronous Vibrations on Large Size Tilting Pad Journal Bearings and Comparison with Analytical Predictions Mirko Libraschi (GE Oil & Gas Nuovo Pignone, Florence, Italy), Oscar Crosato , Michael Catanzaro , Silvia Evangelisti Lecture T9
TAMU Turbo Show 2013 Impact of piping impedance and acoustic characteristics on centrifugal compressors surge and operating range Klaus Brun (Southwest Research Institute, San Antonio, TX), Marybeth G. Nored (Apache, Inc., Houston, TX), Rainer Kurz (Solar Turbines, Inc., San Diego, CA) Lecture T10
TAMU Turbo Show 2013 CO2 Corrosion on Natural Gas Compressors, Criteria and Guidelines Andre Varella Guedes (PETROBRAS, Rio de Janeiro, Brazil), Rodrigo de Carvalho Ferreira (PETROBRAS, Rio de Janeiro, Brazil), Fabio de Norman et d'Audenhove (PETROBRAS, Rio de Janeiro, Brazil), Bruno da Silva Marques (PETROBRAS, Rio de Janeiro, Brazil) Lecture T11
TAMU Turbo Show 2013 History of Evolution, Progress and Application of Safe Diagram for Tuned and Mistuned Systems Murari Singh (Safe Technical Solutions, Inc, Bethlehem, PA) Lecture T12
TAMU Turbo Show 2013 Shop Rotordynamic Testing - Options, Objectives, Benefits and Practices John Kocur (ExxonMobil Research and Engineering, Fairfax, VA), Hunter Cloud (BRG Machinery Consulting, LLC, Charlottesville, VA) Tutorial T1
TAMU Turbo Show 2013 Range Versus Efficiency - Striking the Proper Balance Jim Sorokes (Dresser-Rand, Olean, NY) Tutorial T2
TAMU Turbo Show 2013 Combustion, Fuels and Emissions for Industrial Gas Turbine Combustion Michael Welch (Siemens, Lincoln, UK), Brian Igoe (Siemens, Lincoln, UK) Tutorial T3
TAMU Turbo Show 2013 Electric motors and drives in torsional vibration analysis and design Timo Holopainen (ABB Motors and Generators, Helsinki, Finland), Pieder Jorg (ABB Drives and Controls, Zürich, Switzerland), Jouko Nïiranen (ABB Drives and Controls, Helsinki, Finland), Davide Andrea (ABB Mining, Dättwil, Switzerland) Tutorial T4
TAMU Turbo Show 2013 Gas Turbine Performance and Maintenance Rainer Kurz (Solar Turbines Incorporated, San Diego, CA), Cyrus Meher-Homji (Bechtel Corporation, Houston, TX), Klaus Brun (Southwest Research Institute, San Antonio, TX), Jeff Moore (Southwest Research Institute, San Antonio, TX), Francisco Gonzalez (Enterprise Products, Houston, TX) Tutorial T5
TAMU Turbo Show 2013 Rotating Component Modal Analysis and Resonance Avoidance - Update Frank Kushner (Frank Kushner Consulting, Delmont, PA), Robert Strickland (The Elliott Group, Jeannette, PA), James Shurina (The Elliott Group. Jeannette, PA) Tutorial T6
TAMU Turbo Show 2013 Design Considerations for Revamp/Re-Rate Centrifugal Compressors James Sorokes (Dresser-Rand, Olean, NY), Steven Kaulius (Dresser-Rand, Bethlehem, PA), Edmund Memmott (Dresser-Rand, Olean, NY) Tutorial T7
TAMU Turbo Show 2013 Torsional Natural Frequencies, Measurement versus Prediction Qingyu Wang (Elliott Group, Jeannette, PA), Brian Pettinato (Elliott Group, Jeannette, PA), Troy Feese (Engineering Dynamics Inc., San Antonio, TX) Tutorial T8
TAMU Turbo Show 2013 Development and Design of Antisurge and Performance Control System for Centrifugal Compressor Saul Mirsky (Compressor Controls Corporation, Des Moines, IA), Wayne Jacobson (Compressor Controls Corporation, Des Moines, IA), David Tiscornia (Compressor Controls Corporation, Houston, TX), Jeff McWhirter (Compressor Controls Corporation, Houston, TX), Medhat Zaghloul (Compressor Controls Corporation, Abu Dhabi, UAE) Tutorial T9
TAMU Turbo Show 2013 VSDS Motor Inverter Design Concept for Compressor Trains Avoiding Interharmonics in Operating Speed Range Volker Hutten (Siemens Energy Sector, Duisburg, Germany), Tim Krause (Siemens Energy Sector, Duisburg, Germany), Vijay Anantham Ganesan (Siemens Industry, Nuremberg, Germany), Christian Beer (Siemens Energy Sector, Erlangen, Germany), Sven Demmig (Siemens Industry Sector, Nuremberg, Germany) Tutorial T10
TAMU Turbo Show 2013 Panel Discussion on Subsea Compression Applications Jose Gilarranz (Dresser-Rand, Houston, TX), Urs Baumann (MAN Diesel & Turbo, Zurich, Switzerland), Francesco Bongini (GE Oil & Gas, Florence, Italy), Pal Hedne (Statoil AS, Stavanger, Norway), William Maier (Dresser-Rand, Olean, NY), Michael McKee (INTECSEA, Houston, TX), Manuele Bigi (GE Oil & Gas, Florence, Italy) Tutorial T11
TAMU Turbo Show 2013 Operations and Maintenance of Un-Spared Compressor Trains and their Auxiliary Systems Bryan Barrington (LyondellBasell, Corpus Christi, TX), Phillip Terrano (Dresser-Rand, Olean, NY), Robert Felton (ExxonMobil, Baytown, TX) Tutorial T12
TAMU Turbo Show 2013 Analysis of Rotor Rub in a Large Centrifugal Refrigeration Compressor Neetin Ghaisas (Fluor Canada Ltd.) CST1
TAMU Turbo Show 2013 Morton effect experienced during a mechanical running test of a centrifugal compressor Martin Maier, Glenn Grosso (Dresser-Rand, Olean, NY) CST2
TAMU Turbo Show 2013 Field Investigation of Gearbox Vibration Due to Cracked Motor Rotor Bars Troy Feese (Engineering Dynamics Incorporated, San Antonio, TX), Ross Pinner (Lufkin Industries, TX) CST3
TAMU Turbo Show 2013 Axial Vibration for a Synchronous Motor Driven Gear and In-line Compressor Train Lucy Zhao CST4
TAMU Turbo Show 2013 Hydrogen Flaking Gear Failure in a Centrifugal Compressor Matthew Barausky, Patrick Smith (Air Products) CST5
TAMU Turbo Show 2013 Troubleshooting a Large, Two Stage Diaphragm Compressor Gregory Frantz, Robert Eizember (DuPont), Jose Vazquez (BRG Machinery Consulting) CST6
TAMU Turbo Show 2013 Innovative Design in Expander Wheel-Shaft Attachment Replaces Hirth Coupling for High Speed, High Temperature and High Power Applications Houman Shokraneh (L.A. Turbine, Valencia, CA) CST7
TAMU Turbo Show 2013 Hydrogen compressor seal case study John Justak (ATGI) CST8
TAMU Turbo Show 2013 Resolving intermittent vibration spikes on steam turbines Rajakumar Thiagarajan,, Ashraf Abdelrahim,, and Sankar Ganesh;, representing RasGas and GE CST9
TAMU Turbo Show 2013 Bearing Frosting Ed Czechowski (FS-Elliott), Chris Napoleon (Napoleon Engineering), Mike Tursky (FS-Elliott) CST10
TAMU Turbo Show 2013 Influence of Jacking Oil Grooves in Two-Lobe Bearings on Bearing Performance Henning Ressing (MAN Diesel & Turbo SE) CST11
TAMU Turbo Show 2013 Experience on system electro-mechanical optimization against torsional issues Michele Guidi, Alessandro Pescioni (GE Oil & Gas) CST12
TAMU Turbo Show 2013 Successful online and offline cleaning of steam turbines without disassembly Bladimir Gomez (PDVSA CRP Refinery), Barry Snider (Small Hammer Incorporated) CST13
TAMU Turbo Show 2013 Compressor Oil Flow Kevin Yates (Dow Chemical Company, Freeport, TX) CST14
TAMU Turbo Show 2013 Oil Contamination for Ammonia Chiller Compressor Abdulkareem Al-Ghamdi (Saudi International Petrochemical Co.), Ali Shallwani (Saudi International Petrochemical Co.) CST15
TAMU Turbo Show 2013 Deep Off-Shore Combustion Air Filtering System Analysis Fernando Markovits (PETROBRAS, Brazil), Francisco Carlos (PETROBRAS)br>Orlando Guerreiro (PETROBRAS), Jim Benson (Camfil Farr Power Systems), Joshua Kohn (Camfil Farr Power Systems) CST16
TAMU Turbo Show 2013 How a SIL2 certified protection system prevented major damages to a critical reciprocating compressor on 3 occasions over a 45 day period Eric Miller (DuPont), Skip Morrison (Prognost Systems, Inc.) CST17
TAMU Turbo Show 2014 Computational Investigation of Coupling Guard Heating and Mitigation Vishal Jariwala, Daryll Turner, James Hardin (Elliott Group) Lecture
TAMU Turbo Show 2014 Meeting Motor Driven Compressor Base Package Design Requirements for Service on Floating Production Storage and Offloading Vessels Edward Abraham and Harry Miller (Dresser-Rand) Lecture
TAMU Turbo Show 2014 Overview of Important Considerations in Wet Gas Compression Testing and Analysis Grant O. Musgrove and Melissa A. Poerner (Southwest Research Institute), Massimiliano Cirri (GE Global Research), Matteo Bertoneri (GE Oil & Gas) Lecture
TAMU Turbo Show 2014 Development of High-Pressure Ratio and Wide-Operation Range 700bar Compressor Shinichiro Tokuyama (Mitsubishi Heavy Industries Compressor Corporation), Diogo Yoshikazu Ujihara (Petróleo Brasileiro), Akihiro Nakaniwa and Satoshi Saburi (Mitsubishi Heavy Industries, Ltd.) Lecture
TAMU Turbo Show 2014 The Challenge for the Accurate Determination of the Axial Rotor Thrust in Centrifugal Compressors Yves Bidaut and Dominique Dessibourg (MAN Diesel&Turbo Schweiz AG) Lecture
TAMU Turbo Show 2014 Manufacturing and Testing Experience with Direct Metal Laser Sintering for Closed Centrifugal Compressor Impellers Timothy C. Allison, Aaron M. Rimpel, J. Jeffrey Moore, Jason C. Wilkes (Southwest Research Institute); Robert Pelton, Karl Wygant (Samsung Techwin) Lecture
TAMU Turbo Show 2014 Honeycomb Seal Effect on Rotor Response to Unbalance Leonardo Baldassarre, Andrea Bernocchi, Leonardo Failli, Michele Fontana, Nicola Mitaritonna, Emanuele Rizzo (General Electric Oil & Gas) Lecture
TAMU Turbo Show 2014 Optimization of Swirl Brake Design and Assessment of Its Stabilizing Effect on Compressor Rotordynamic Performance Leonardo Baldassarre, Andrea Bernocchi, Michele Fontana, Alberto Guglielmo, Guido Masi (General Electric Oil & Gas Company) Lecture
TAMU Turbo Show 2014 Stability Testing of CO2 Compressors Roberto F. de Noronha, Marcelo Accorsi Miranda (PETROBRAS), Katia Lucchesi Cavalca (Campinas State University), Edmund A. Memmott, Krish Ramesh (Dresser-Rand Company) Lecture
TAMU Turbo Show 2014 Axial Subsynchronous Vibration Scan DeCamillo (Kingsbury, Inc.) Lecture
TAMU Turbo Show 2014 Centrifugal Compressor Rotordynamics in Wet Gas Conditions Giuseppe Vannini, Giuseppe Del Vescovo, and Matteo Bertoneri (GE Oil & Gas); Melissa Wilcox (Southwest Research Institute) Lecture
TAMU Turbo Show 2014 Testing of Gas-Liquid Centrifugal Separation and Compression Technology at Demanding Operating Conditions William Maier, José L. Gilarranz R., Yuri Biba, Daniel DeMore (Dresser-Rand) Lecture
TAMU Turbo Show 2014 Gas Turbine Degradation Rainer Kurz (Solar Turbines, Inc.), Klaus Brun (Southwest Research Institute), Cyrus Meher-Homji (Bechtel) Tutorial
TAMU Turbo Show 2014 Combustion, Fuels and Emissions for Industrial Gas Turbines Michael Welch and Brian M. Igoe (Siemens Industrial Turbomachinery Ltd.) Tutorial
TAMU Turbo Show 2014 Subsea Compression Applications José L. Gilarranz R and William C. Maier (Dresser-Rand), Urs Baumann (MAN Diesel & Turbo), Manuele Bigi (GE Oil & Gas), Stein Jørgensen (Aker Solutions AS), Alberto Milani (GE Oil & Gas) Thomas Eldridge (Shell) Tutorial
TAMU Turbo Show 2014 Fundamentals of Signal Processing Applied to Rotating Machinery Diagnostics Gaston H. Desimone (GE Measurement & Control) Tutorial
TAMU Turbo Show 2014 Monitoring of a Dry Gas Seal’s Secondary Seal Glenn Schmidt (DGS Glenn), Rich Hosanna (John Crane Inc.), Vladimir Bakalchuk (Flowserve Corporation), Jim McCraw (BP America Inc.) Tutorial
TAMU Turbo Show 2014 Save your Centrifugal Machinery during Commissioning Arun Kumar and Mohit Sabharwal (HPCL-Mittal Energy Ltd.) Tutorial
TAMU Turbo Show 2014 Revamp/Re-Rate Design Considerations James M. Sorokes, Steven T. Kaulius, Edmund A. Memmott (Dresser-Rand) Tutorial
TAMU Turbo Show 2014 Driver Selection for Mechanical Drive Service Vinod Patel (KBR), Shawn Walth (KBR), Mark Weatherwax (Chevron), Rainer Kurz (Solar Turbines), Cyrus Meher-Homji (Bechtel Corp.), Gampa Bhat (Mitsubishi Compressor International Corp.) Tutorial
TAMU Turbo Show 2014 Technology Machinery Engineers Need to Know to Work Effectively Subsea: Part 1 of 2 Dag Elvebakken (Aker Solutions), Jonah Margulis (Aker Solutions), Zenon Medina-Cetina (Texas A&M University), Michael Mancuso (OneSubsea) Tutorial
TAMU Turbo Show 2014 New Active Magnetic Bearing Requirements for Compressors in API 617 Eighth Edition Erik Swanson (Xdot Engineering and Analysis), Andrea Masala (Waukesha Bearings), Lawrence Hawkins (Calnetix, Inc.) Tutorial
TAMU Turbo Show 2014 Technology Machinery Engineers Need to Know to Work Effectively Subsea: Part 2 of 2 Dag Elvebakken (Aker Solutions), Jonah Margulis (Aker Solutions), Zenon Medina-Cetina (Texas A&M University), Michael Mancuso (OneSubsea) Tutorial
TAMU Turbo Show 2014 A Review of Aerodynamically Induced Forces Acting on Centrifugal Compressors, and Resulting Vibration Characteristics of Rotors James M. Sorokes, Mark J. Kuzdzal, D. Fred Marshall (Dresser-Rand) Tutorial
TAMU Turbo Show 2014 Examples of Balancing Methods: Four-Run and Least-Squares Influence Coefficients Troy Feese (Engineering Dynamics Inc.) Case Study
TAMU Turbo Show 2014 Coupled Torsional-Lateral Analysis Staffan Lundholm, Niklas Sehlstedt, Per Tellefsen, Claus Myllerup (Lloyd’s Register) Case Study
TAMU Turbo Show 2014 CGC Large Steam Turbine Vibration Resonance of Pedestal and Linkage System RCA, Detail Vibration Investigation/Measurement at Site and Countermeasures Makoto Katagake, Kyoichi Ikeno, Satoshi Hata (Mitsubishi Heavy Industries) Case Study
TAMU Turbo Show 2014 Remote Monitoring and Diagnostics as Applied to a Reciprocating Compressor Head Bruce McCain (Oxy Oil and Gas Corporation) Case Study
TAMU Turbo Show 2014 Investigation and Analysis of High Thrust Bearing Temperature After Field Overhaul and Rerate of a Centrifugal Compressor Barry J. Blair (Waukesha Bearings Corporation), James M. Byrne (BRG Machinery Consulting), Stephen L. Ross (Elliott Company), Jonathan Toner (ExxonMobil) Case Study
TAMU Turbo Show 2014 RTD Failure for Hydrodynamic Thrust Bearing Hatem Abdelrahman and Mohamed Maysara (MOPCO, Egypt), Paolo Farnararo (GE Oil & Gas) Case Study
TAMU Turbo Show 2014 Two Pole Motor Vibration Diagnostics, Analysis and Solution Yu Zhao (BHP Billiton), Nelson Baxter (ABM Technical Services) Case Study
TAMU Turbo Show 2014 2x Pinion Vibration Problems and Solutions for Motor-Gear-Compressor Trains During Commissioning Presenter: Qingyu Wang (Elliott Group) Case Study
TAMU Turbo Show 2014 Coupling Failure Due to a Motor Fault Clay McClinton (Chevron), Dan Phillips and Joe Corcoran (Kop-Flex) Case Study
TAMU Turbo Show 2014 Improved Inlet Filtration Membrane Helps Resolve Blade Liberation Events on Large Axial Compressors Wilson Poon, Thomas Davidson (Linde LLC) Case Study
TAMU Turbo Show 2014 Acoustic Instability in Pilot-Operated Pressure Safety Valves Timothy Allison and Klaus Brun (Southwest Research Institute) Case Study
TAMU Turbo Show 2014 Application of Hydraulic Coupling Bolts (Sleeve Type) to High Cycle Loaded Reciprocating Compressor Francesco Caprioli, Simona Allio, Stefan Norberg (SKF), Guido Pratelli (GE Oil & Gas) Case Study
TAMU Turbo Show 2014 Dry Gas Seal Failures in a Recycle Gas Centrifugal Compressor, Causes and Remedial Actions Vasanth Bhat (Singapore Refining C. Pte. Ltd.), Jim Demetriou (Chevron Energy Technology Co.) Case Study
TAMU Turbo Show 2014 Investigating Root Causes of Catu Compressor Station Shut-Down Due to High Discharge Temperature Eduardo Merçon, Pablo Adolfo Nogueira, Paulo Bruno Peres, Ricardo Pinheiro, Rodrigo Mourão (Petrobras) Case Study
TAMU Turbo Show 2015 Coupled Torsional and Lateral Analysis for the Determination of the Damping of the First Torsional Mode of Synchronous Motor Driven Compressor Trains Jean-Claude Pradetto, Urs Baumann (MAN Diesel & Turbo Schweiz AG) Lecture T01
TAMU Turbo Show 2015 Practical Guidelines For Oil & Gas Plant Design Against Sub-Synchronous Torsional Interaction Phenomena Federico Svetti, Paola Rotondo, Daniele Sgro, Francesco Meucci (GE Oil & Gas) Lecture T02
TAMU Turbo Show 2015 Development and Testing of Multi-Stage Internally Cooled Centrifugal Compressor Jason Kerth, Jorge Pacheco (Dresser-Rand), Jeffrey Moore, Tim Allison, Neal Evans (SWRI) Lecture T03
TAMU Turbo Show 2015 Measured Effects Of Liquid Distribution On Compressor Performance During Wet Gas Ingestion Grant Musgrove, Griffin Beck (SWRI), Michael Matheidas and Stan Uptigrove (ExxonMobil) Lecture T04
TAMU Turbo Show 2015 The Effect Of Starvation On The Dynamic Properties Of Tilting Pad Journal Bearings John Whalen (John Crane), Vaclav Cerny, Vaclav Polreich (Doosan Skoda Power), Minhui He (BRG Machinery Consulting) Lecture T05
TAMU Turbo Show 2015 High Performance Bearing Comparison Josh Ronan, Thomas Shoup, Gwenael Perney, Chad Robertson (Lufkin), Bernard Quoix, Alain Gelin (Total E&P) Lecture T06
TAMU Turbo Show 2015 Operational modal analysis application for the measure of logarithm decrement in centrifugal compressor Alberto Guglielmo, Leonardo Baldassarre and Michael Catanzaro (GE), Leandro de Oliveira Zague, Leonardo Ishimoto, Marcelo Accorsi Miranda, Raphael Timbo Silva (Petrobras) Lecture T07
TAMU Turbo Show 2015 A Novel Method for Measurement and Evaluation of Torsional Damping for Geared Turbomachinery During Operation Using Lateral Vibration Probes Staffan Lundholm, Stefano Morosi, Niklas Sehlstedt, Anders Crone and Petter Pehrson (Lloyd's Register Consulting) Lecture T08
TAMU Turbo Show 2015 Measuring and Modeling Vertical Crosshead Vibration in API-618 Reciprocating Compressors Brian Howard, Charles Hatch (GE Bently Nevada), Gregory Yonker (Dresser-Rand), Kevin Philips (BP West Coast Products) Lecture T09
TAMU Turbo Show 2015 Numerical Prediction And Experimental Validation Of Rotor Thermal Instability Daniele Panara, Leonardo Baldassarre (GE), Duccio Griffin, Alessandro Mattana, Simone Panconi and Enrico Meli (University of Florence) Lecture T10
TAMU Turbo Show 2015 Axial Thrust in High Pressure Centrifugal Compressors: Description of a Calculation Model Validated by Experimental Data from Full Load Test Michele Fontana, Leonardo Baldassarre, Andrea Bernocchi, Emanuele Rizzo, Francesco Maiuolo (GE) Lecture T11
TAMU Turbo Show 2015 Applying CFD to Solve a Vibration Problem of a Compressor Roberto Firmento de Noronha, Diogo Yoshikazu Ujihara (PETROBRAS), Leticia de Rezende Tapajoz (CENPES), Glenn Grosso (Dresser-Rand) and Ridrigo Peralta Muniz Moreira (ESSS) Lecture T12
TAMU Turbo Show 2015 Equation 1a, with the "Velocity of Sound in the Material" & "Poisson's Ratio," Allows Quick & Remarkably Accurate Prediction of New Natural Frequencies for Modes of Vibration of Machinery & Structures When Changing Material & Size .T. Myrick, Jr. (S.T. Myrick, Jr., PhD, LLC) Lecture T13
TAMU Turbo Show 2015 Hydrodynamic Torque Converters For Oil & Gas Compression And Pumping Applications: Basic Principles, Performance Characteristics And Applications Klaus Brun (SWRI), Christoph Meyenberg (Voith Turbo), Joseph Thorp (Aramco Services), Rainer Kurz (Solar Turbines, Inc.) Tutorial T01
TAMU Turbo Show 2015 Explosive Decompression And Other O-Ring Related Issues For Turbomachinery Service- Some User Guidance Chris Carmody (AESSeal) Tutorial T02
TAMU Turbo Show 2015 Causes Of Subsynchronous Vibration In Integrally Geared Compressors Evan B. Williams, John R. Badini (FS-Elliott) Tutorial T03
TAMU Turbo Show 2015 Fundamentals of Fluid Film Journal Bearing Operation and Modeling Minhui He, Hunter Cloud, James Byrne and Jose Vazquez (BRG Machinery Consulting, LLC) Tutorial T04
TAMU Turbo Show 2015 Tips for Troubleshooting with the Operating Deflection Shape (ODS) Technique Ramon A. Silva, Kyle J. Kuecker (Engineering Dynamics Inc.) Tutorial T05
TAMU Turbo Show 2015 Meeting Compression Train Base Package Design Requirements for Service on Floating Production Storage and Offloading Vessels Harry Miller, Edward Abraham (Dresser-Rand) Tutorial T06
TAMU Turbo Show 2015 Introduction of a New Family of Steam Turbine Low Pressure Stages - A Comprehensive Review of 10 Years of Experience in Design, Manufacturing, Experimental Validation and Field Application orenzo Cosi (GE Oil & Gas) Tutorial T07
TAMU Turbo Show 2015 Applying API 617, 8th Edition to Expander-Compressors with Active Magnetic Bearings Jeff Smithanik, Yannick Paul (SKF) Tutorial T08
TAMU Turbo Show 2015 Range Versus Efficiency – Striking The Proper Balance Jim Sorokes (Dresser-Rand) Tutorial T09
TAMU Turbo Show 2015 Review of Centrifugal Compressors High Pressure Testing for Offshore Applications Leonardo Ishimoto, Marcelo Accorsi Miranda, Raphael Timbo Silva (Petrobras), Fabio de Norman et d'Audenhove (Royal Dutch Shell), Edmund Memmott and Gary Colby (Dresser-Rand) Tutorial T10
TAMU Turbo Show 2015 Gas Turbine Air Filtration Systems For Offshore Applications Rainer Kurz (Solar Turbines), Dominique Orhon (Total E&P), Stephen Hiner (CLARCOR Industrial Air) and Jim Benson (Camfil Farr Power Systems) Tutorial T11
TAMU Turbo Show 2015 A New Approach to Designing Centrifugal Compressor Surge Control Systems Jordan Grose (Beta Machinery Analysis), Kamal Botros (Nove Chemicals), Steven Hill (Williams Gas Pipelines) Tutorial T12
TAMU Turbo Show 2015 Fit For Purpose Unique Machinery Repair Techniques for Late In Life Production Facilities Authors: Stan Uptigrove, Chin Tze-Hur, Karl Edward (ExxonMobil Exploration and Production Malaysia Inc.) CST01
TAMU Turbo Show 2015 CFD Study Of Failure In An Oil Flooded Screw Compressor Journal Bearing Authors: Diogo Yoshikazu Ujihara, Marcelo Accorsi Miranda, Mateus Louis Vieira (Petrobras), Lucilla Almeida, Rodrigo Peralta M. Moreira (Engineering Simulation Scientific Software, Brazil) CST02
TAMU Turbo Show 2015 FCCU PRT Compressor Blade Failure Case Study Authors: Austin Anderson (CITGO), Chris Sykora and Tony Rubino (RMS) CST03
TAMU Turbo Show 2015 Export Gas Compressors Verecon Vibration Analysis Authors: Chandra Sivapuram (NCPOC), Rogan Stewart (Shell), Basso DeGregorio (ENi) CST04
TAMU Turbo Show 2015 Gearbox Sub-Synchronous Radial Vibration at the Train 1st TNF, Induced by Cyclic Process Phenomena Authors: Gaspara Maragioglio Paola Rotondo, Gianluca Boccadamo, Valerio Depau (GE Oil & Gas) CST05
TAMU Turbo Show 2015 Gear lateral vibrations caused by VSD interharmonic interference with torsional natural frequencies Authors: Staffan Lundholm, Rasmus Kristensen, Niklas Sehlstedt (Lloyd's Register Consulting), Leif l. Myklebust (Statoil) CST06
TAMU Turbo Show 2015 Analysis and on-stream countermeasures of High Thrust Bearing Temperature of A Centrifugal Compressor Authors: Kim BumSu, Lee SangJoo, Sin SangMun and Lee SangSuk (SK Innovation) CST07
TAMU Turbo Show 2015 Oil & Gas plant experience of Sub-Synchronous Torsional Interactions (SSTI) and operability optimization Authors: Paola Rotondo, Daniele Sgro, Giuliano Milani, Giacomo Tucci (GE Oil & Gas) CST08
TAMU Turbo Show 2015 Applying Rotordynamics Analysis to Identify the Cause of High Synchronous Vibration on Overhung-Rotor Compressor Author: Manuel Marin (Equistar Chemical, LP) CST09
TAMU Turbo Show 2015 Pipe Vibration Caused by Aero Excitation Resulted from a Foreign Object Lodged Inside an Impeller Passage Authors: Zheji Liu, Mark Kuzdzal, Scott Wisler (Dresser-Rand) CST10
TAMU Turbo Show 2016 Full Speed String Test on GE LM6000PF Gas Turbine Driven Refrigeration Compressors Sameer Patwardhan, Feroz Meher-Homji (Bechtel Oil, Gas & Chemical), Mark Weatherwas (Chevron Energy Technolovy Pty Ltd), Davide Cappetti, Antonio Musardo, Gianni Iannuzi (GE Oil & Gas) Lecture T01
TAMU Turbo Show 2016 Development of Fuel-Flexible Gas Turbine Combustor Tomohiro Asai, Keisuke Miura, Yasuhiro Akiyama, Mitsuhiro Karishuku, Keita Yunoki, Satoschi Dodo, Nobuyuki Horii (Mitsubishi Hitachi Power Systems, Ltd.) Lecture T02
TAMU Turbo Show 2016 Effect of Relative Journal Bearing and Honeycomb Seal Direct Stiffness on Radial Synchronous Vibrations of High-Pressure Centrifugal Compressors Michele Fontana, Leonardo Baldassarre, Andrea Bernocchi, Michele Moretti (GE Oil & Gas) Lecture T03
TAMU Turbo Show 2016 Subsynchronous Vibrations on Turboexpanders Equipped with Magnetic Bearings Assessment, Understanding and Solutions Laurent Richaume, Bernard Quiox (TOTAL), Houman Shokraneh (L.A. Turbine), Matthieu Oliva (SKF Magnetic Mechatronics (S2M)) Lecture T04
TAMU Turbo Show 2016 Coupling Guard Temperature and Windage Power Loss: CFD Analysis and Experiments Adam Thompson (John Crane Ltd), Tianbo Zhai, Alan Palazzolo (Texas A&M University), Amir Keshmiri (Manchester Metropolitan University) Lecture T05
TAMU Turbo Show 2016 Electromagnetic Effects on the Torsional Natural Frequencies of an Induction Motor Driven Reciprocating Compressor with a Soft Coupling Troy Feese (Engineering Dynamics Incorporated), Aleksander Kokot (WEG Equipamentos Eletricos S.A.) Lecture T06
TAMU Turbo Show 2016 Adapting Hermetically Sealed Compressor Technology to Deal With Sour and Corrosive Gases Marcel Buse, Mark van Aarsen (Dresser-Rand), Eyad Al-Khateeb, Bader Al-Jughaiman (Saudi Aramco) Lecture T07
TAMU Turbo Show 2016 Impeller Stall Induced by Reverse Propagation of Non-uniform Flow Generated at Return Channel Keizo Yoneda, Shinji Iwamoto, Akihiro Nakaniwa, Shinichiro Tokuyama, Hirofumi Higuchi (Mitsubishi Heavy Industries Compressor Corporation), Bryan Barrington (LyondellBasell Global Engineering Services) Lecture T08
TAMU Turbo Show 2016 Application of Dynamic Pressure-Balanced Seals in a Multistage Centrifugal Compressor Mark Kuzdzal, Harry Miller, Charles Rohrs (Dresser-Rand), David Stiles (Hess Oil), John Justak (ATGI), Ed Wilcox (Chevron ETC), Mark R. Sandberg (STC LLC) Lecture T09
TAMU Turbo Show 2016 Full Scale Validation of a High Pressure Ratio Centrifugal Compressor Stefano Falomi, Giuseppe Iurisci, Stefano Fattori, Angelo Grimaldi, Carlo Aringhieri, Giuseppe Sassanelli, Gianni Iannuzzi (GE Oil & Gas) Lecture T10
TAMU Turbo Show 2016 Aero-Damping Measurements and Computation in a Full-Scale Multistage Centrifugal Compressor Lorenzo Toni, Francois Moyroud, Giuseppe Gatta, Dante Tommaso Rubino, Alberto Guglielmo (GE Oil & Gas), Kishore Ramakrishnan (GE Global Research) Lecture T11
TAMU Turbo Show 2016 Performance Test of a Liquid Tolerant Impeller and Validation of Wet Compres Stefano Falomi, Luca Scarbolo, Matteo Bertoneri, Veronica Ferrara (GE Oil & Gas) Lecture T12
TAMU Turbo Show 2016 Basic Thermodynamics of Reciprocating Compression Greg Phillippi (Ariel Corporation) Tutorial T01
TAMU Turbo Show 2016 Comparison of Two- and Four-Pole VSD Motors up to 4000 RPM Timo Holopainen (ABB Motors and Generators), Pieder Joerg, Olli Liukkonen (ABB Drives and Controls) Tutorial T02
TAMU Turbo Show 2016 Gas Turbine Packaging Options and Features Klaus Brun (Southwest Research Institute), Rainer Kurz, Bernhard Winkelman (Solar Turbines, Inc), Joseph Thorp (Aramco Services Company) Tutorial T03
TAMU Turbo Show 2016 Your Gas Compression Application - Reciprocating, Centrifugal or Screw? Ben Williams, Greg Phillippi (Ariel Corporation), Bruce McCain (Oxy Midstream), Tim Manthey (Aerzen USA), Jonathan Sutter (Elliott Group) Tutorial T04
TAMU Turbo Show 2016 Rotor Balancing Tutorial Dustin Pavelek, Ray Kelm, Walter Kelm (Kelm Engineering, LLC) Tutorial T05
TAMU Turbo Show 2016 Centrifugal Compressor Configuration, Selection and Arrangement: A User's Perspective Mark R. Sandberg (Independent Consultant) Tutorial T06
TAMU Turbo Show 2016 Vibration Analysis for Turbomachinery Ed Wilcox (Chevron ETC) Tutorial T07
TAMU Turbo Show 2016 A CFD Primer: What Do All Those Colors Really Mean? James M. Sorokes (Dresser-Rand), Jim Hardin (Elliott Group), Brad Hutchinson (ANSYS, Inc.) Tutorial T08
TAMU Turbo Show 2016 Squeeze Film Dampers: An Experimental Appraisal of Their Dynamic Performance Sung-hwa Jeung (Texas A&M University), Luis San Andres (Turbomachinery Laboratory, Texas A&M University), Sean Den (Formosa Plastics Corp.), Gregory Savela (Pratt & Whitney Engines, UTC) Tutorial T09
TAMU Turbo Show 2016 Subsea Compression - Current Technology and Its Use to Maximize Late Life Production Markus Dettwyler, Dirk Buche, Urs Baumann (MAN Diesel & Turbo Schweiz AG) Tutorial T10
TAMU Turbo Show 2016 A Review of Aerodynamically Induced Forces Acting on Centrifugal Compressors, and Resulting Vibration Characteristics of Rotors James M. Sorokes, Mark Kuzdzal (Dresser-Rand, Siemens Power and Gas Division), Fred Marshall (Dresser-Rand) Tutorial T11
TAMU Turbo Show 2016 Compressor Loadsharing Control and Surge Detection Techniques Serge Staroselsky, Michael Tolmatsky, Medhat Zaghloul, Wayne Jacobson (Compressor Controls Corporation), Jeff McWhirter (Independent Consultant) Tutorial T12
TAMU Turbo Show 2016 Resolving Cyclic Vibration on an Instrument Air Compressor Amit Sharma, Nicolas Peton (GE Oil & Gas - Bently Nevada) CST01
TAMU Turbo Show 2016 Sub-Synchronous Vibration on Centrifugal Compressor with Tilt-Pad Bearings John J. Yu (GE Oil & Gas), Nicholas Hanson (Flint Hills Resources) CST02
TAMU Turbo Show 2016 Analysis and On-Stream Countermeasures of Sub-Synchronous Vibration of a Centrifugal Compressor Sangjoo Lee (SK Energy) CST03
TAMU Turbo Show 2016 Torsional Instability of Cooling Tower Fan during Induction Motor Start-Up Akira Adachi (Toyo Engineering Corporation), Brian Murphy (Rotating Machinery Analysis, Inc.) CST04
TAMU Turbo Show 2016 Redesign of Centrifugal Compressor Impeller by means of Scalloping Kirill Grebinnyk (Sulzer), Rob Widders (BOC) CST05
TAMU Turbo Show 2016 Improving Reliability and Reducing Steam Leakage in General Purpose Steam Turbines with Floating Brush Seals Jongsoo Kim (Waukesha Bearings Corporation), Peter Zanini (Waukesha Bearings), Jeff Sandridge (RCM Sales & Services), Billy Gilmore Jr. (Chevron Pascagoula Refinery) CST06
TAMU Turbo Show 2016 Continuous Control of Lube Oil Water Contamination - Never Get Surprised Again Steve Locke (the Chemours Company) CST07
TAMU Turbo Show 2016 Integral Gear Compressor Gearbox Flooding Issue Daryl L Callan (Air Products and Chemicals, Inc.) CST08
TAMU Turbo Show 2016 Asynchronous Motor - Failure of Rotor Lamination Teeth Alain Gelin, Bernard Quoix, Antoine Lucas (TOTAL), Xavier Coudray, Guillaume Delhaye, Nicolas Velly (GE Power Conversion) CST09
TAMU Turbo Show 2016 A High Bearing Temperature Troubleshooting of Centrifugal Heat-Pump Compressor Woonsil Lee, Chi Hyuk Kim (Hyundai Oilbank Co.), An Sung Lee (KIMM) CST10
TAMU Turbo Show 2016 New Control Method for Fixed Speed Compressors with Side Stream David Rossi, Marco Pelella, Laurence Casali (GE Oil & Gas) CST11
TAMU Turbo Show 2016 Double Flow Refrigeration Compressor Inlet Piping Design and Analysis Jeremy Hayes, Vince Mankowsk (ExxonMobil Research & Engineering), Pablo Bueno (Southwest Research Institute) CST12
TAMU Turbo Show 2016 Why Proper Low Pass Filtering Settings on Crosshead Vibration Signals Are Crucial to Minimize Risk of Missed Detects Oliver Franz (PROGNOST Systems, Inc.), Robert C. Eisenmann Jr. (BP) CST13
TAMU Turbo Show 2016 Investigation of Process Gas Compressor Shaft Vibration Phenomena Ashutosh Vengurlekar (ExxonMobil Research & Engineering, Singapore), Teo Woon Lip (ExxonMobil), Nathan Little (ExxonMobil Research & Engineering), Satoru Yoshida (Mitsubishi Heavy Industries Compressor Corporation) CST14
TAMU Turbo Show 2016 Investigation of Steam Turbine Blade Failure Ashutosh Vengurlekar (ExxonMobil Research & Engineering, Singapore, Robert D Fisher (ExxonMobil Research & Engineering), Yuki Nakamura, Yuichi Sasaki, Satoshi Hata, Kyoichi Ikeno (Mitsubishi Heavy Industries Compressor Corporation) CST15
TAMU Turbo Show 2017 Torsional Modal Damping of a LCI Driven Geared Moto-compressor Train: Evaluation, Optimization Criteria and Active Control Gaspare Maragioglio (GE Oil & Gas), Daniele Sgro (GE Oil & Gas), Paolo Calore (GE Oil & Gas), Lorenzo Failla (GE Oil & Gas), Pierluigi Tenca (GE Global Research Center) Lecture T01
TAMU Turbo Show 2017 Forced Response Analysis in a Full-scale Multistage Centrifugal Compressor: Imeller Vibration Prediction and Validation Dr. Lorenzo Toni (GE Oil & Gas - Nuovo Pignone), Dr. Alberto Guglielmo (GE Oil & Gas - Nuovo Pignone), Dr. Francois Moyroud (GE Oil & Gas - Thermodyn), Dr. Giuseppe Gatta (GE Oil & Gas - Nuovo Pignone), Dr. Dante Tommaso Rubino (GE Oil & Gas - Nuovo Pignone), Giacomo Scarabello (GE Oil & Gas - Nuovo Pignone) Lecture T02
TAMU Turbo Show 2017 A More Comprehensive Evaluation of Equation of State Influences on Compressor Performance Determination Mark R. Sandberg (Sandberg Turbomachinery Consulting, LLC) Lecture T03
TAMU Turbo Show 2017 Improving LNG Facility Reliability and Operability Via OEM Integrated Comppressor Controls Daniele Galeotti, Antonio Baldassarre, Leonardo Baldassarre (GE Oil & Gas), Dave Ramlakanm, Hans Weyermann, Paul Broadway (ConocoPhillips Company) Lecture T04
TAMU Turbo Show 2017 High Frequency Vibrations on Gears Dietmar Sterns (RENK Aktiengesellschaft), Dr. Michael Elbs (ISMB Dautermann GmbH) Lecture T05
TAMU Turbo Show 2017 Experimental Evaluation of Mechanical Reliability of the Impeller Blade for Large Integrally Geared Compressors Takuya Iwata, Yoshitaka Baba, Keiichi Saeki, Yuki Kameyama (Kobe Steel, Ltd.), Tsukasa Shiga (Kobelco Compressors America, Inc.) Lecture T06
TAMU Turbo Show 2017 Design and Testing of a High-Pressure-Ratio Centrifugal Stage - Probing the Aerodynamic & Mechanical Limits James M. Sorokes, Kirk Lupkes, Ravi Srinivasan, Mark Kuzdal, Dave J. Peer, Silvano Saretto (The Dresser-Rand Business) Lecture T07
TAMU Turbo Show 2017 Advancing Compressor Dynamic Simulation Fidelity with use of Field Data George Talabisco, Jon Paul Van Buskirk (The Dresser-Rand Business) Lecture T08
TAMU Turbo Show 2017 Electrical Damping of VFD Induced Torsional Torque Pulsations in a LCI Driven Compressor Drive Train Vijay Ganesan, Max Beuermann, Peter Kalbfleisch, Martin Hilscher (Siemens AG) Lecture T09
TAMU Turbo Show 2017 Subsynchronous Shaft Vibration in an Integrally Geared Expander-Compressor due to Vortex Flow in an Expander Daisuke Hirata, Naoyuki Nagai, Hirotaka Higashimori (Mitsubishi Heavy Industries) Lecture T10
TAMU Turbo Show 2017 Rotordynamic Test Results from a High Flexibility Ratio - High Pressure Fully Instrumented Centrifugal Compressor Test Vehicle Hiuseppe Vannini, Emanuele Rizzo, Antonio Pelagotti, Carmine Camicino (GE Oil & Gas) Lecture T11
TAMU Turbo Show 2017 Optimizing Component Selection in Synchronous Motor Compressor Trains Based on Technical and Financial Considerations Martin D. Maier, Garry Studley (The Dresser-Rand Business) Tutorial T01
TAMU Turbo Show 2017 Process Control with Industrial Gas Turbines Rainer Kurz (Solar Turbines Incorporated), Klaus Brun (Southwest Research Institute), Joseph Thorp (Aramco Services Company) Tutorial T02
TAMU Turbo Show 2017 Torsional Excitation Upon Short-Circuit in Induction Motors - in Conventional and High-Speed Trains Tuomo Aho, Christopher Baum (MAN Diesel & Turbo Schweiz AG), Janne Nerg (Lappeenranta University of Technology) Tutorial T03
TAMU Turbo Show 2017 Turbomachinery Overview for Supercritical CO2 Power Cycles Timothy C. Allison, J. Jeffrey Moore, Jason C. Wilkes, Klaus Brun (Southwest Research Institute) Tutorial T04
TAMU Turbo Show 2017 Tutorial on Large Steam Turbine Systems in Oil & Gas Applications Emmanuel Bustos, Mounir Mossolly, Guillaume Herve (TechnipFMC) Tutorial T05
TAMU Turbo Show 2017 Assessing and Computing the SafetyIntegrity Level (SIL) for Turbomachinery Protection Curt Miller (SIS SILverstone LLC), Justin Kassie (Tesoro), Dan Poston (LyondellBasell) Tutorial T06
TAMU Turbo Show 2017 Electric-Motor-Driven Gas Compressor Packages: Starting Methods for Large Electrical Motors and Torsional Integrity Michael Glasbrenner (Voith Turbo GbmH & Co. KG), Balaji Venkataraman, Chester Lee, Rainer Kurz (Solar Turbines Incorporated), Ge' Juan Cole (Williams Gas Pipeline) Tutorial T07
TAMU Turbo Show 2017 Turbomachinery Control Valves Sizing and Selection Medhat Zaghloul (Compressor Controls Corporation) Tutorial T08
TAMU Turbo Show 2017 A CFD Primer: What Do All Those Colors Really Mean? James M. Sorokes (The Dresser-Rand Business), James Hardin (The Elliott Group), Brad Hutchinson (Ansys, Inc.) Tutorial T09
TAMU Turbo Show 2017 Strategies to Prevent Sudden Catastrophic Compressor Failures During Transient Operating Conditions Patrick J. Smith (Air Products & Chemicals, Inc.) Tutorial T10
TAMU Turbo Show 2017 Centrifugal Compressor Performance Making Enlightened Analysis Decisions B. Fred Evans, Spencer Huble (Chiyoda International Corp.) Tutorial T11
TAMU Turbo Show 2017 Range Versus Efficiency - Striking The Proper Balance James M. Sorokes (The Dresser-Rand Business) Tutorial T12
TAMU Turbo Show 2017 Torsional Failure on Reciprocating Compressor Package Ken Atkins, James Clark (Engineering Dynamics, Inc.) CST01
TAMU Turbo Show 2017 Pelletizer Motor Bearing Damage Detection Based on Vibration Data John J. Yu (GE Oil & Gas), Carl Feng Wang, Tony Wei Zhou (Shanghai SECCO Petrochemical Co.), Nicolas Peton, Haibo Lin, Jun Quan (GE Oil & Gas) CST02
TAMU Turbo Show 2017 Prediction and Mitigation of High Vibrations During Hot Restart of Centrifugal Compressors Leonardo Baldassarre, Michele Fontana, Andrea Bernocchi, Gianluca Conte, Mirko Libraschi (GE Oil & Gas) CST03
TAMU Turbo Show 2017 Thrust Balance Line Bolts Failure Felix Cestari, Robert Briggs, Regis Fowler (Siemens), Ge Jiangang (PWPC PetroChina) CST04
TAMU Turbo Show 2017 Reliability Improvement for Booster Reciprocating Compressor in CCR Reformer Sanguk Lee, Bumsu Kim, Sangsuk Lee, Sangjoo Lee (SK Energy Ulsan) CST05
TAMU Turbo Show 2017 Reciprocating Compressor Optimization Kelsy Holmes, Pablo Castillo, Bruce McCain (Oxy Oil and Gas Corporation) CST06
TAMU Turbo Show 2017 Severe Corrosion on Rotor Blades of Back Pressure Type Steam Turbine Due to Unique Reason. What Went Wrong? Arun Kumar (HPCL-Mittal Energy Ltd.), Anurag Chopra (HMEL Refinery) CST07
TAMU Turbo Show 2017 Damaged Compressor Stator Parts - Resulting From Operation in Deep Choke Jean-Claude Pradetto, Urs Baumann (MAN Diesel & Turbo Schweiz AG) CST08
TAMU Turbo Show 2017 Compander Vibration Troubleshooting Sebastien Jaouen (Cryostar), CLiff Bower (MOL/CS Yamal Project), Stephane Berger (Flender-Graffenstaden), Alain Gueraud (Cryostar) CST09
TAMU Turbo Show 2017 Eliminating a Rotordynamic Instability of a 12 MW Overhung, Radial Inflow Expander Chris D. Kulhanek, J. Jeffrey Moore (SOuthwest Research Institute), Joseph Lillard, Grant Nordwall (Atlas Copco Gas and Process), Greg Elliott, Tom Shoup (GE Oil & Gas) CST10
TAMU Turbo Show 2017 Gas Turbine with Rotor Crack Vibration Diagnostics Peter Popaleny, Nicolas Peton (GE Oil & Gas) CST11

Copyright © 2017 Rotating Machinery Analysis, Inc.. All rights reserved.